Desa Wall Mantel and Base W32LT Скачать руководство пользователя страница 1

Note: Gather all mantel pieces together before assembling 

mantel.

  WARNING:  Use  only  1/2"  screws  to  attach  metal 

angle brackets. Damage to mantel will result if other 

screws are used for this purpose.

AssemblING mANtel

ImPORtANt: more than one person is required to as-

semble and lift mantel.

Estimated assembly time: 45 minutes.
When assembling mantel do not tighten screws completely 

until told to do so. There should be some play in the pieces 

to allow for proper alignment and best possible fit. It is very 

important that more than one person assemble mantel together. 

Panels must be held in proper alignment to each other while 

tightening screws to assure fewer gaps and proper surface 

alignment. When tightening screws, do not over tighten. This 

may cause threads to strip. For this reason, the supplied Al-

len wrench should be used rather than a power screwdriver. 

Panels  have  threaded  inserts  installed  at  screw  locations. 

Screws should start and turn easily in threaded holes when 

assembled  according  to  instructions.  Do  not  force  screws 

into holes.

IMPORTANT

: There is a serial number label inside of right 

side panel and on outside package. When calling to request 

technical assistance or for replacement parts please have 

that number ready.

W32LT WaLL ManTeL and Base

asseMBLY and InsTaLLaTIOn InsTRUCTIOns

Important:

 Read entire instruction sheet before 

assembling or installing mantel kit.
the  W32lt  mantel  is  only  approved  for  use  with 

any DESA Heating, LLC 32" fireplace system and 
universal  fireplace.  Do  not  use  mantel  with  any 

other product.

This mantel kit contains the following:

•  Mantel pieces - unassembled and marked as follows:

  #1 Base
  #2 Right Side with arrow
  #3 Right Front Leg with arrow
  #4 Left Side with arrow
  #5 Left Front Leg with arrow
  #6 Header with arrow
  #6A Header Extension
  #7 Top

•  Hardware Kit*
   16 - Metal Brackets 

118937-01

   32 - Screws M6 x 12 mm (1/2") 

121149-01

   20 - Screws M6 x 30 mm (1 

1

/

4

") 

121335-01

  20 - Washers M6 

121336-01

  1 - Allen Wrench 

121337-01

  * Extra hardware may be included.
If  any  wood  pieces  are  missing  or  damaged,  contact  the 

dealer where you purchased this mantel for replacement. If 

hardware is missing or damaged, contact DESA Heating, LLC 

at 1-866-672-6040 for referral information. You can also visit 

DESA Heating, LLC’s web site at 

www.desatech.com

.

www.desatech.com

Содержание Wall Mantel and Base W32LT













Отзывы: