background image

Aesthetic Technology Limited

16

17

PL-027 (Rev 7)

PL-027 (Rev 7)

WARNING! 

Use of accessories, transducers and cables other than those 

specified or provided by the manufacturer of this equipment could result 
in increased electromagnetic emissions or decreased electromagnetic 
immunity of this equipment and result in improper operation.

Only use the power adapter and accessories supplied along with detachable parts with 
the system or specified by the manufacturer and rated for country of use. Using any 
other adapter may lead to an electrical fault or could result in increased electromagnetic 
emissions or decreased electromagnetic immunity of this equipment and result in improper 
operation

To fully isolate the device from the mains power, unplug from the mains outlet socket. 
Ensure the mains outlet socket is always accessible.

The power lead supplied with the unit may present a trip hazard if installed incorrectly 
or in the main footpath of operation. Always take caution when manoeuvring around the 
product. 

The power lead may present itself as a strangulation hazard to infants if not correctly installed. 

Always plug the system into a direct mains outlet socket. Do not use an extension cable or 
socket adaptor. 

Do not use the system near water/liquids or where water/liquids could be spilt onto it. 

Do not use the system if the LED Array has come into contact with water/liquids.

Do not plug, unplug or activate the system with wet hands. 

Do not use the system in the presence of flammable liquids or gases. 

Do not disassemble any parts from the system. Opening or removing covers may expose 
the operator to dangerous voltages or other risks. Incorrect reassembly may lead to an 
electric shock. 

Do not operate or handle the device when powered if it is damaged in any way. Contact 
Aesthetic Technology Ltd or your local Dermalux® representative for advice. If the LED 
Array is damaged and powered it poses no risk to the user or operator due to low voltage 
supply. 

Do not attempt to modify the system in any way as this may result in an electric shock 
when the system is used again. Unauthorised modification will also void the warranty. 

Portable RF communications equipment (including peripherals such as antenna cables 
and external antennas) should be used no closer than 30 cm (12 inches) to any part of the 
Dermalux® Flex MD, including cables specified by the manufacturer. Failure to take notice 
of this warning may result in degradation of the device.

WARNING! 

Avoid use around children and animals to prevent unnecessary risk.

The Dermalux® Flex MD system is an electrical device, which under certain circumstances 
could present an electrical shock hazard to the user. Please follow the directions stated in 
the manual and online training to assure maximum safety during operation.

Содержание FlexMD


























Отзывы: