manualshive.com logo in svg

Deprag AST40-1, Руководство по эксплуатации

Поделиться
Скачать
Deprag AST40-1 Скачать руководство пользователя страница 56

 

56 

7.6.2.4.5 Data backup 

The "Save values" command can be used as often as desired in the screwdriver operation, 
but however, only the last three values are saved. In case of an error or a failure, the 
values are always saved. 
The value last saved is always available in the range Step_3 / Torque_3 / Angle_3. 
When using the "Save values" command multiple times in the screwdriver program, the 
previous values are shifted upwards (Step_3 

 Step_2 

 Step_1). 

If an error occurs during the screwdriver operation, the screw fixing values of the incorrect 
step are saved in the range Step_NOk / Torque_NOk / Angle_NOk. 
 
Example: 

 

 

7.6.2.5 Ethercat 

Available on request. 
 

 

fd_Step3 

fd_Step3 

 fd_Step2 

fd_Step3 

fd_Step2 

 fd_Step1 

fd_Step3 

 fd_Step2 

fd_Step3 

fd_Step2 

 fd_Step1 

fd_Step3 

 fd_Step2 

fd_Step3 

fd_StepNOk 

Содержание AST40-1


























































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды