manualshive.com logo in svg

Deprag AST40-1, Руководство по эксплуатации

Поделиться
Скачать
Deprag AST40-1 Скачать руководство пользователя страница 117

 

117 

12.1.5 Find 

The screwdriving sample find can be used to facilitate threading the screw. 

Sequence of the Screwdriving Strategy: 

At the start of the screwdriving level the time monitoring and the angle measurement are 
started. 
Cyclic torque measurements are performed. 

Switching -Off Criteria: 

The screwdriving sequence is completed when 

•  switching off angle or the shut-off torque is reached 
•  the maximum screwdriving time (monitoring time) is expired 

Evaluation: 

OK evaluation:

 

The screwdriving level is considered OK (fault free), if the switching off occurs 
via the angle of rotation or the torque. 

Not OK evaluation: 

The screwdriving level is evaluated as Not OK (faulty) if the torque is outside 
the set limits or the screwdriving time has been exceeded. 

Parameters: 

The following parameters are used in the screwdriving sample: 

•  Maximum time until the switching off angle is reached (monitoring time) 
•  Switching off angle 
• Shut-off torque 
•  Torque upper limit 
• Speed  
•  End value creation: End torque/maximum torque 

Selectively the result torque can be displayed as end torque (torque at end of 
screwdriving) or the maximum torque (maximum occurred torque) in the end values. 
 
 

Содержание AST40-1


























































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды