Denyo DLW-300LS Скачать руководство пользователя страница 33 | Manualshive

Страница: 33 / 50

Denyo DLW-300LS Скачать руководство пользователя страница 33

- 31 -

8-9 AC Power Supply

          AC power supply
           This machine is provided with AC power supplies in addition to the welding power

supply. Mount terminal to each tip (connection part) of the cable and cord without
fail, and fasten the screw securely.

       (1) Be sure to turn off the circuit breaker for AC power source before connecting
           AC loads.  Connecting without turning off can cause a death accident due to
           electrical shock or give a electrical damage to the machine.

       (2) Do not allow overloading when AC and DC are used simultaneously. The circuit
           breaker trips automatically when AC current exceeds the maximum output.

         [ NOTE ]

[ NOTE ]

[ NOTE ]

[ NOTE ] : Where high quality welding is required, do not use the AC power

source simultaneously.

AC output Capacity for lamp at simultaneous use with DC output

AC power supplies are used concurrently

welding rod

AC power source capacity allowable for simultaneous use

Single-Phase 8.3/9.1 kVA or Three-Phase 10.4/11.4 kVA

φ2.0 (50A)

Single-Phase 7.2/8.0 kVA or Three-Phase 9.0/10.0 kVA

φ2.6 (100A)

Single-Phase 5.9/6.7 kVA or Three-Phase 7.3/8.3 kVA

φ3.2 in use(150A)

Single-Phase 4.4/5.2 kVA or Three-Phase 5.5/6.5kVA

φ4.0 in use(200A)

Single-Phase 2.7/3.5 kVA or Three-Phase 3.3/4.3 kVA

φ6.0 in use(250A)

Single-Phase 0.8/1.6 kVA or Three-Phase 1.0/2.0 kVA

φ6.0 in use(300A)

0

   (3) Do not allow the AC output to connect to house wiring or commercial supply wiring.

   (4) This welder/generator is equipped with four single-phase receptacles(option) and

one single-phase output terminal(option) for auxiliary power, which have can be used for
a particular auxiliary load with a maximum combined output of 3.0 kVA or 1.5 kVA per receptacle.
When using both of these receptacles and output terminal at once, for the best results,
it is recommended that each receptacle

’

s output be balanced with each other.

«
...
31
32
33
34
35
...
»

Содержание DLW-300LS



















































Отзывы:

Нет отзывов