DENTSPLY inLab MC X5 Скачать руководство пользователя страница 103

Страница: 103 / 108

64 78 759 D3608

D3608

201.01.07

02 10.2017

103

Dentsply Sirona

7 Maintenance and cleaning

Operating Instructions inLab MC X5

7.11 Error messages and measures

båÖäáëÜ

7.11

Error messages and measures

In the event of an error, the machine outputs error messages. Refer to the

following table for measures to be taken for the respective error.

Error message

Action

Error in the air circuit of the spindle sealing

air.

Please check the compressed air supply (7 bar). If the error persists,

contact customer service.

Error in the air circuit of the tool change

cylinder.

Please check the compressed air supply (7 bar). If the error persists,

contact customer service.

Error in the blast air circuit.

Please check the compressed air supply (7 bar). If the error persists,

contact customer service.

Error in the air circuit of the boost valve

(pressure increase).

Please check the compressed air supply (7 bar). If the error persists,

contact customer service.

The water pump reported an error.

Please check that there is enough water in the tank or that the inlet and

outlet are properly connected.

The suction device reported an error.

Please check that the suction device is connected and switched on or,

for wet processing, is switched off. Please also check that the plugs are

properly connected.

The spindle reported an error.

Please check the state of the tools. If the tools are heavily worn out,

replace them and re-start the process.

Internal software error.

Please re-start the machine. If the error persists, contact customer

service.

No system pressure was detected.

Please check the compressed air supply (7 bar). If the error persists,

contact customer service.

Unspecified communication error. Please

try again.

Unspecified communication error. Please try again. If the error persists,

contact customer service.

Time-out occurred during order processing

Unspecified communication error. Please try again. If the error persists,

contact customer service.

The suction device reported an error.

Please check that the suction device is connected and switched on and

check that the plug is properly connected.

The suction device reported an error.

Please check that the suction device is switched off.

No valid calibration data available.

Please contact customer service.

The door lock reported an error.

Please check that the door is properly locked. If the error persists,

contact customer service.

The cover of the instrument tray cannot be

closed.

Please check that the lock of the magazine is closed.

The chuck cannot be opened.

Please check the compressed air supply (7 bar). If the error persists,

contact customer service.

The chuck cannot be closed.

Please check the compressed air supply (7 bar). If the error persists,

contact customer service.

No tool detected.

Please check that each tool is connected correctly.

The tool could not be removed and is still

secure in the chuck.

Please try again to change the tool or change the tool manually using

the spindle maintenance in the machine configuration. Clean the chuck

using the accompanying maintenance kit.

The tool sensor reported an error.

Please clean the sensor and then manually actuate it a few times. If the

error persists, contact customer service.

Содержание inLab MC X5













































































































Результаты поиска

Содержание inLab MC X5

Отзывы:

Бренды по названию

Популярные бренды

DENTSPLY inLab MC X5, Руководство по эксплуатации

Результаты поиска

Содержание inLab MC X5

Отзывы:

Бренды по названию

Популярные бренды