Dentsply Sirona DAC Universal Touch Скачать руководство пользователя страница 27

Страница: 27 / 124

Dentsply Sirona
Operating Instructions DAC Universal

3 Product description

3.3 Programs

6681006 D3708
D3708.201.01.01.02 04.2019

3.2.9

Error LED

The DAC Universal is equipped with an LED.

This flashes in the event of an error. If the error is relevant for the
process, an alarm also sounds.

3.3

Programs

The DAC Universal automatically recognizes which lid has been
inserted into the DAC Universal.

A reprocessing cycle in the DAC Universal is counted once the "

Start"

function key is pressed. It also counts if an error appears or the cycle is
discontinued while the lid is being closed.

Program for Blue lid

Tem-
perature

max. tem-
perature

Absolute
pressure (in
bar)

Disinfection
time

Total cycle
duration*

Program

134 °C

137 °C

3.2 bar

30 sec.

ca. 15 min

Blue standard program lid

* with factory settings

Program for Green lid

Tem-
perature

max. tem-
perature

Absolute
pressure (in
bar)

Disinfection
time

Total cycle
duration*

Program

134 °C

137 °C

3.2 bar

30 sec.

ca. 14 min

Green program lid

* with factory settings

Содержание DAC Universal Touch





























































































































Результаты поиска

Содержание DAC Universal Touch

Отзывы:

Dentsply Sirona DAC Universal Touch, Руководство по эксплуатации, Страница: 27 / 124

Результаты поиска

Содержание DAC Universal Touch

Отзывы: