Denon D-T1 Скачать руководство пользователя

Страница: 40 / 51

3. VFD is not lit

4. The disc is not ejected

Check the power supply of the VFD driver

(VFD14V)

MAIN PCB

[FB1]

Voltage is input as normal.

When the "

" button is pressed, there is no

discharge sound from the disk that runs the

motor.

Check the operation of the "

" button

MAIN PCB (ADC_KEY1)

[XP10 : 9pin]

The voltage changes to around 0V when the "

button is pressed.

Check the state / soldering for the following

parts.

MAIN PCB

[U5, U6, U10]

Check the surrounding circuits.

Check the power supply of the VFD driver (+5VA)

DISPLAY PCB

[U1 : 14, 38pin]

Voltage is input as normal.

Check the power supply of the VFD driver (-24V)

MAIN PCB

[U25 : 1, 3pin]

Voltage is input as normal.

[R25, R29]

Voltage is input as normal.

Check the operation of the VFD driver

DISPLAY PCB

[U1 : 5, 6, 8, 9pin]

No issues in the data line between the VFD driver

and the MCU.

[15-37pin]

No issues in the control line of the VFD.

Check the operation of the VFD (filament)

DISPLAY PCB

[VFD1 : 1, 2, 31, 32pin]

Filament voltage (pulse) is supplied as normal.

Defect in the VFD

DISPLAY PCB

Check or replace the soldering of [VFD1].

Check the state / soldering for the following

parts.

MAIN PCB

Check the circuits around [Q7].

Replace the mechanical.

（Remove the disc by undoing the mecha

screws.）

Check the state / soldering for the following

parts.

DISPLAY PCB

[SW1, ESD1, XP4]

MAIN PCB

[XP10, FB37, R132]

Check the surrounding circuits.

Check the state / soldering for the following

parts.

DISPLAY PCB

[R30, R31, ZD2, C17, C18]

Check the state / soldering for the following

parts.

MAIN PCB

Check the circuits around [U25].

Check the circuits around [D1, D2, Q8].

Check the following

MAIN PCB-DISPLAY PCB

Check of [U10-U1]Data Line.

DISPLAY PCB

[U1]

Check the circuits around [U1].

(U1 may be defective)

Check the state / soldering for the following

parts.

DISPLAY PCB

Check the circuits around [Q1, Q2, Q3, Q4, Q5,

ZD1].

YES

Before Servicing

This Unit

Electrical

Mechanical

Repair Information

Updating

Содержание D-T1



















































Результаты поиска

Содержание D-T1

Отзывы:

Похожие инструкции для D-T1

Бренды по названию

Популярные бренды

Denon D-T1, Руководство по обслуживанию

Результаты поиска

Содержание D-T1

Отзывы:

Похожие инструкции для D-T1

Бренды по названию

Популярные бренды