Denon AVR-S710W, Руководство по обслуживанию

Страница: 19 / 169

SPECIAL MODE
Special mode setting button (for AVR-X1200W)
b
No. 1 - 6, 9 : While holding down buttons " A ", " B " and " C " simultaneously, press the power button to turn on the power.
b
No. 7, 8 : While the power is on, hold down buttons " A " and " B " for at least 3 seconds .
b
No. 10 : While holding down buttons " A " and " B " simultaneously, insert the AC plug into the wall outlet to turn on the power.
No. Mode Button A Button B Button C Descriptions
1
Version Display
(u-COM / DSP Error Display)
DIMMER STATUS -
Displays the version of firmware such as the main firmware or DSP.
Errors that have occurred are displayed.
( See page 21 )
2
Selecting the Mode for Service-related
ZONE2
SOURCE
DIMMER STATUS
This is a display for turning on each service-related mode.
Service-related modes: No. 2-1 - No. 2-5
2-1 Protection history display mode
TUNER
PRESET CH
+
- -
Displays the protection occurrence history.
( See page 44 )
2-2
Check the Video/Audio path Mode ↑ - -
This is a special mode for service confirmation used during repair
work to simplify the confirmation work for the Audio channel /
video channel.
( See page 27 )
2-3
Remote ID Setup Mode ↑ - -
If there are multiple DENON AV receivers in the same area, this
mode prevents other AV receivers from being operated concur-
rently with this device.
( See page 48 )
2-4
TUNER STEP Mode
(E3 and E2 model only)
↑ - -
Enables reception STEP of the ANALOG TUNER to be changed.
( See page 47 )
2-5
Operation Info Mode ↑ - -
Displays the accumulated operating time of the unit, the number
of times the power was switched on, and the number of occur-
rences of each protection.
( See page 46 )
3 User Initialization Mode
TUNER
PRESET CH
-
TUNER
PRESET CH
+
-
Initializes backup data.
(Settings for the Installer Setup are not initialized.)
4
Factory Initialization Mode
ZONE2
SOURCE
DIMMER -
Initializes backup data.
(The settings for the Installer Setup is also initialized.)
5
PANEL / REMOTE LOCK Selection Mode
TUNER
PRESET CH
+
ZONE2
SOURCE
-
Start this unit in the PANEL/REMOTE LOCK selection mode so that
PANEL LOCK and Remote Lock can be switched between ON and
OFF.
( See page 25 )
6 Protection Pass Mode
TUNER
PRESET CH
+
ZONE2
SOURCE
STATUS
Enables the power to be turned on when protection detection is
disabled.
( See page 49 )
7 CY920 Reboot Mode
TUNER
PRESET CH
-
TUNER
PRESET CH
+
- The CY920 is restarted after CY920 hang up.
8
CY920 Initialization Mode
ZONE2
SOURCE
DIMMER -
Enter this mode only after replacing Flash for CX870 / CY920 and
rewriting the firmware.
9
USB Update Mode
ZONE2
SOURCE
TUNER
PRESET CH
-
- Switches this unit to USB Update mode.
10
Forced USB All Device Write Mode
TUNER
PRESET CH
+
STATUS -
Mode used when this unit cannot be recovered.
Forcibly switches this unit to USB update mode.
( See page 56 )
QUICK SELECT
MASTER VOLUME
SOURCE SELECT
ZONE2
ON/OFF
ZONE2
SOURCE
DIMMER STATUS
TUNER
PRESET CH
DVD/Blu-ray ONLINE
MEDIA
PLAYER
CBL/SAT
3 2 1 4
PHONES SETUP MIC AUX - HDMI
5V/1A
DIMMER
STATUS TUNER
PRESET CH -
TUNER
PRESET CH + X
ZONE2
SOURCE
19