115
Speakers
Setting items
Setting details
Levels
Set the volume of the test
tone to be the same when it
is output from each speaker.
Test Tone Start
: Output test tone.
•
Front L
/
F.Height L
/
Center
/
F. Height R
/
Front R
/
Surround R
/
Surr. Back R
z
/
Surr. Back L
z
/
Surround L
/
Subwoofer
: Select
speaker to output test tone.
z
When the “Speaker Config.” – “Surr. Back” setting (
) is
set to “1spkr”, “Surr. Back” is displayed.
•
–12.0dB – +12.0dB
(0.0dB)
: Adjust the volume.
When “Levels” is adjusted, the adjusted values are set for all the sound
modes.
NOTE
•
Speakers set to “None” in the “Speaker Config.” (
)
settings are not displayed.
•
When a headphones jack is inserted in the PHONES jack of this unit, the
“Levels” is not displayed.
Set Defaults
: The “Levels” settings are returned to the default settings.
•
Yes
: Reset to the defaults.
•
No
: Do not reset to the defaults.
When you select “Set Defaults” and press
ENTER
, the “Reset to the default values?”
prompt is displayed. Select either “Yes” or
“No”, and press
ENTER
.
Setting items
Setting details
Crossovers
Set the maximum frequency
of the bass signal output
from each channel to
the subwoofer. Set the
Crossover Frequency to
suit the bass reproduction
capability of the speaker
being used.
Crossover
: Set the crossover frequency.
•
40Hz
/
60Hz
/
80Hz
/
90Hz
/
100Hz
/
110Hz
/
120Hz
/
150Hz
/
200Hz
/
250Hz
/
Individual
: Set the crossover frequency for all speakers. See the
speaker manual for information concerning speaker crossover frequency.
The following settings can be set when the “Crossover” setting is set to
“Individual”.
•
Front
/
Center
/
Surround
/
Surr. Back
/
Front Height
: Select speaker
for setting of crossover frequency.
•
40Hz
/
60Hz
/
80Hz
/
90Hz
/
100Hz
/
110Hz
/
120Hz
/
150Hz
/
200Hz
/
250Hz
: Set the crossover frequency.
•
“Crossovers” can be set when the “Bass” – “Subwoofer Mode”
(
) setting is “LFE+Main”, or when you have a speaker that
is set to “Small”.
•
Always set the crossover frequency to “80Hz”. When using small
speakers, however, we recommend setting the crossover frequency to
a higher frequency.
•
For speakers set to “Small”, sound below the crossover frequency
is cut from the sound output. The cut bass sound is output from the
subwoofer or front speakers.
•
The speakers that can be set when “Individual” is selected differ
depending on to the “Subwoofer Mode” setting (
•
When “LFE” is selected, speakers set to “Small” at “Speaker Config.”
can be set. If the speakers are set to “Large”, “Full Band” is displayed
and the setting cannot be made.
•
If set to “LFE+Main”, this setting can be made regardless of the
speaker size.
Front Speaker Setup
Set the front speakers to
use for every sound mode.
NOTE
This can be set when “Amp
Assign” is set to “Front B”
(
2ch Playback
: The front speakers used in direct play (2 channel), stereo
play and pure direct play (2 channel) are set in advance.
•
A
: Front speaker A is used.
•
B
: Front speaker B is used.
•
A+B
: Both front speakers A and B are used.
Multi ch Playback
: The front speakers used in play modes other than
direct play (2 channel), stereo play and pure direct play (2 channel) are set
in advance.
•
A
: Front speaker A is used.
•
B
: Front speaker B is used.
•
A+B
: Both front speakers A and B are used.
Basic v
ersion
A
dv
anced v
ersion
Inf
or
mation
A
dv
anced v
ersion
DVD
