Deltadoors LiftMaster AA250EVK, Руководство по установке

Страница: 20 / 62

19
LED
Error
code
Issue Possible reason Solution
E5
Press transmitter, but no gate
movement.
1) STOP swtich is open. 1) Check if STOP switch is open or damaged.
2) STOP switch is not connected.
2) Check if STOP switch is disconnected. If yes, then reconnect
STOP switch or change the respective Input setting to other value.
E7
Press transmitter, but no gate
movement.
Control board amplifier for Motor 1 fail.
Switch off power for 20 seconds and reset to check if control board
recovers. If not, change control board.
E8
Press transmitter, but no gate
movement.
Control board amplifier for Motor 2 fail.
Switch off power for 20 seconds and reset to check if control board
recovers. If not, change control board.
E9
Press transmitter, but no gate
movement.
Control board memory mistake.
Switch off power for 20 seconds and reset to check if control board
recovers. If not, change control board.
F1
Motor 1 stop and reverse
during open or close.
Motor 1 is blocked. Check and remove obstruction. Clean gate.
F2
Motor 2 stop and reverse
during open or close.
Motor 2 is blocked. Check and remove obstruction. Clean gate.
F3
Motor 1 stop and reverse
during open or close.
Motor 1 stall or speed sensor is damaged. Check if motor 1 stalled or speed sensor is damaged.
F4
Motor 2 stop and reverse
during open or close.
Motor 2 stall or speed sensor is damaged. Check if motor 2 stalled or speed sensor is damaged.
F5
Press transmitter, but motor
has no action.
Radio module fail.
Switch off power for 20 seconds and reset to check if control board
recovers. If not, change control board.
F6 Gate reverse during closing. Low battery power. Charge battery.
F7
Press transmitter, but no gate
movement.
Control board damaged.
Switch off power for 20 seconds and reset to check if control board
recovers. If not, change control board.
F9
Press transmitter or push
button, but motor has no
action.
AP menu is reset to factory default. Relearn limits.
LE Motor stops suddenly. Press C button during limit learning. Relearn limits.
9. ERROR CODES
AA250EVK
Input Voltage VAC 220-240
Input frequency Hz 50/60
Motor Voltage VDC 24V
"Standby consumption
(without accessories)"
W 3.2
Motor Rated Power W 100W (AA250-24P) 50W (AA250-24S)
Rated Load Nm 72,4
Maximum Torque Nm 200
Cycles per hour 10
Max. cyles per day 30
Max. wing width / weight m / kg
1.5m / 250kg
2.0m / 200kg
2.5m / 150kg
Max. opening angle 120°
Time to open to 90° s 13-15
End Limit System Encoder with hard stops
Operating Radio Frequency
Sending Power
MHz
RX 433MHz
(433.30MHz, 433.92MHz, 434.54MHz)
RX 868MHz
(868.30MHz, 868.95MHz,
869.85MHz)
TX 865.125MHz, 865.829MHz,
866.587MHz
<10mW
Code S 2.0
Max. nr of remotes 180
Max. nr. of keypads 4
Max. nr. of myQ devices 16
AA250EVK
External accessory power 24VDC - max. 500mA
Flahing lamp connector 24VDC - max. 500mA
E-Lock /Magnetic lock conenctor 24VDC - max. 500mA
External relay 24VDC - max. 500mA
Safety edge 8,2 kOhm
Max. nr. of IRs 3
Max. nr. of external inputs 3
Battery back-up unit 2 x 12V, 2.2Ah batteries model 490EV
Ingress Protection Motor IP 44
Noise Level dB < 70 db(A)
Working temperature °C -20°C to +55°C
Weight (kit) Kg 20
Transmitter Frequency
TX4EVF
868MHz (868.30MHz, 868.95MHz,
869.85MHz)
Sending power <10mW
Battery CR2032 3V
10. TECHNICAL DATA