Delta DRP048V060W1B Series, Техническое описание

Страница: 12 / 17

TECHNICAL DATASHEET
CliQ II DIN Rail Power Supply
48 V 60 W 1 Phase / DRP048V060W1B

All parameters are specified at 25°C ambient and AC input unless otherwise indicated.
www.DeltaPSU.com (September 2021, Rev. 06)
12
Power Boost
𝐷𝐷𝐷𝐷𝐷𝐷𝐷𝐷 𝑐𝑐𝐷𝐷𝑐𝑐𝑐𝑐𝑐𝑐 (%) =
𝑇𝑇
𝑃𝑃
𝑇𝑇𝑇𝑇𝐷𝐷𝑇𝑇𝑐𝑐 𝑇𝑇𝑇𝑇𝑇𝑇𝑐𝑐
𝐴𝐴𝐴𝐴𝑐𝑐𝐴𝐴𝑇𝑇𝐴𝐴𝑐𝑐 𝑂𝑂𝐷𝐷𝐷𝐷𝑂𝑂𝐷𝐷𝐷𝐷 𝑃𝑃𝑇𝑇𝑃𝑃𝑐𝑐𝐴𝐴 ( 𝑃𝑃
𝐴𝐴𝐴𝐴𝐴𝐴
) =
( 𝑃𝑃𝑇𝑇𝑃𝑃𝑐𝑐𝐴𝐴 𝐵𝐵𝑇𝑇𝑇𝑇𝐵𝐵𝐷𝐷 × 𝑇𝑇
𝑃𝑃
) + ( 𝑁𝑁𝑇𝑇𝑁𝑁 - 𝑃𝑃𝑐𝑐𝑇𝑇𝑃𝑃 𝑃𝑃𝑇𝑇𝑃𝑃𝑐𝑐𝐴𝐴 × 𝑇𝑇
𝑁𝑁
)
𝑇𝑇𝑇𝑇𝐷𝐷𝑇𝑇𝑐𝑐 𝑇𝑇𝑇𝑇𝑇𝑇𝑐𝑐
OR
𝑁𝑁𝑇𝑇𝑁𝑁 - 𝑃𝑃𝑐𝑐𝑇𝑇𝑃𝑃 𝑃𝑃𝑇𝑇𝑃𝑃𝑐𝑐𝐴𝐴 =
�𝑃𝑃
𝐴𝐴𝐴𝐴𝐴𝐴
× 𝑇𝑇𝑇𝑇𝐷𝐷𝑇𝑇𝑐𝑐 𝑇𝑇𝑇𝑇𝑇𝑇𝑐𝑐� − ( 𝑃𝑃𝑇𝑇𝑃𝑃𝑐𝑐𝐴𝐴 𝐵𝐵𝑇𝑇𝑇𝑇𝐵𝐵𝐷𝐷 × 𝑇𝑇
𝑃𝑃
)
𝑇𝑇
𝑁𝑁

An example of Power Boost and Average Output Power
Power Boost
Peak Power
(W
P
)
Power Boost
Duration (T
P
)
Duty Cycle
Non-Peak
Power (W
N
)
Non-Peak Power
Duration (T
N
)
Total Time
(T)
150% 90 5 sec 10% 57 W 45 sec 50 sec
150% 90 5 sec 35% 44 W 9.3 sec 14.3 sec
120% 72 10 sec 20% 57 W 40 sec 50 sec
120% 72 10 sec 35% 54 W 18.5 sec 28.5 sec
It is not recommended to prolong the duration of Power Boost to be longer than the specified duty cycle calculation, this may cause
damage to the PSU.
External Input Protection Device
The unit is protected with internal fuse (not replaceable) at L pin and it has been tested and approved on 20 A (UL) and 16 A (IEC) branch
circuits without additional protection device. An external protection device is only required if the supplying branch has an ampacity greater
than above. Thus, if an external protective device is necessary, or, utilized, please refer a minimum value of 8 A B- or 4 A C- characteristic
breaker.
Power Boost is the reserve power available
constantly that allows reliable startup to support
sudden and short spike of loads with high inrush
current typically during turn on to remove the need
of more expensive higher rated power supply unit.
After the output has reached its steady state set
value, the power supply can support surge loads
with a higher short-term power demand up to 150%
of maximum rated load (I
O
Max), for a maximum
duration of 5 seconds. The Power Boost is also
available to repeatedly basis with according to the
condition of an average (R.M.S) output power shall
not exceed continuous operating condition or refer
to duty cycle calculation below.
Fig. 4 Duty Cycle Calculation