1
72639 Rev. C
Models/Modelos/Modèles
59348, 59310 WH 59410, 59710,
59310-WH20-PK, 59310-WH18-
PK, 59348-20-PK, 59348-18-PK
Series/Series/Seria
HAND SHOWER UNIT WITH WALL MOUNT
INSTRUCCIONES PARA LA INSTALACION DE
LA UNIDAD DE LA REGADERA DE MANO CON
SOPORTE DE PARED
INSTRUCTIONS D’INSTALLATION DE LA
DOUCHE À MAIN AVEC SUPPORT MURAL
72639
Write purchased model number here.
Escriba aquí el número del modelo comprado.
Inscrivez le numéro de modèle ici.
07/03/2020
www.deltafaucet.com
1-800-345-DELTA (3358)
?
4 CONNECT TAPERED END OF HOSE TO HAND SHOWER
Seat the washer, if provided, firmly into the hose nut. Remove the yellow tape from the end of the hose that screws onto the hand shower. Carefully align the thread
of the
tapered end
of the Hose directly to the Hand Shower.
Hand tighten
- do not use a wrench or pliers. Then place the Hand Shower into the wall mount.
3. INSTALL SHOWER ARM AND HAND SHOWER
It is recommended to wrap plumber tape (not included) around the threads of the shower arm only.
3A. STANDARD INSTALLATION:
A washer, if provided (some of our hoses are washerless), must be firmly seated into the bottom of the standard hex nut end
of the Hose. Then firmly
hand tighten
the hose nut
clockwise
onto the water supply.
DO NOT
use a wrench or pliers.
If
your Hose has Hose nuts, as pictured
in 3A; a vacuum breaker may be required for installation.
If your hose is not equipped with a vacuum breaker, in order to make your product backflow compliant a vacuum breaker will need to be added.
INSTALLATION WITH A VACUUM BREAKER:
If a Vacuum Breaker is required for your installation, the Vacuum Breaker should be connected to the standard
hex nut of the Hose and then attach it to the Shower Arm at the water supply connection.
If you attach the Vacuum Breaker to the Hand Shower, it will not
function as desired.
3B. VACUUM BREAKER HOSE INSTALLATION:
Your shower hose is equipped with a Vacuum Breaker, permanently installed in the end of your hose that has
a
ridged nut
(as pictured in 3B).
Hand tighten
the ridged nut
clockwise
to the water supply. Do not use a wrench or pliers.
If you attach the ridged nut to
the hand shower, the Vacuum Breaker will not function.
NOTE: A Vacuum Breaker is a device that is required by certain code authorities to protect your water supply from the back-flow of impure water. The Vacuum
Breaker usually
discharges a small amount of water
each time you turn on your shower. It may also
drain water when you shut it off.
Both are normal
conditions – the water is draining not leaking.
DO NOT TRY TO REMOVE OR TIGHTEN THE VACUUM BREAKER
which is permanently installed into the hose. This could cause damage to the
mechanism.
1. REMOVE EXISTING SHOWER HEAD
Turn the existing shower head counter-clockwise with adjustable wrench or pliers. Use care not to unscrew the shower arm; hold the shower arm secure.
Note: If
your shower arm has a ball on the end of it, it will not work with this shower unit and will need to be replaced with a standard shower arm.
2. INSTALL WALL MOUNT
Select wall position desired for your hose length. Prior to mounting, hold up the gray mounting base with the circular handle in an ”up” position. Determine type of
mount for your application.
For mounting into Tile:
Drill 1/4” holes in grout (if possible) and use enclosed anchors and screw mount to base.
For mounting into
Fiberglass/Acrylic:
Drill 1/4” holes (larger if needed for specific toggle bolts) in wall and install with small toggle bolts (not supplied).
For Adhesive Mounting:
Clean the surface area with extra-fine steel wool; then apply rubbing alcohol or fingernail polish remover to prepare the surface and wipe
clean.
Caution: The first position must be correct, as you cannot move the mount after adhering to the surface.
Peel off the green backing film and position
holder upright. Press firmly into place.
ALLOW 24 HOURS BEFORE USING.
Snap shell cover over the base on the wall.
1.
2.
3.
4.
Ridged
Nut
=
3A
=
3B