Delta Tau ACC-72EX Скачать руководство пользователя страница 72 | Manualshive

Страница: 72 / 146

background image

ACC-72EX User Manual

Software setup

72

SOFTWARE SETUP

ACC-72EX supports multiple protocols, and setting up each protocol can be a bit different, as described
in the protocol specific documentation provided by Hilscher. In this section, most of the generic steps are
covered with the help of examples and screenshots.

Required Software Packages

Two software packages are required for setting up ACC-72EX:

1.

SYCON.NET (V1.310.x.x or newer), available through Hilscher’s website.

2.

ACC-72EX Setup Assistant Software.

Both software packages have to be installed on the PC used for initial setup of the system and
commissioning of the machine. Notice that neither of these software packages is required after the initial
setup and the unit can work as a standalone setup.

SyCon.NET Software Setup

SYCON.net is a tool for the configuration of Fieldbus and Real-Time Ethernet systems. It is based on the
standardized FDT / DTM technology. Online diagnostic indicators and auto-scan function for the reading
of network participants assist in the commissioning of the network. SYCON.NET is provided with the
gateway module under license from Hilscher Corporation.

With the power off, plug the ACC-72EX into the UBUS backplane and turn on the power to the UMAC
rack. Connect the diagnostic port to a USB port on the PC using a micro-USB type cable.

Launch the SYCON.NET software on the PC.

Enter the password:

«
...
70
71
72
73
74
...
»

Содержание ACC-72EX



















































































































































Отзывы:

Нет отзывов

Похожие инструкции для ACC-72EX

Бренд: C&H Technologies Страницы: 46

Proventia A1204

Бренд: Internet Security Systems Страницы: 42

IntroSpect Analyzer 2 Series

Бренд: Aruba Страницы: 5

Бренд: Kohler Страницы: 32

GSM7224v2 - Layer 2 Managed Gigabit Switch

Бренд: NETGEAR Страницы: 3

Бренд: IBM Страницы: 130

Бренд: SMC Networks Страницы: 56

Бренд: MiLAN Страницы: 155

Бренд: Aztech Страницы: 13

ExtremeCloud Appliance E3120

Бренд: Extreme Networks Страницы: 27

Бренд: ADTRAN Страницы: 100

Бренд: Tripp Lite Страницы: 2

Бренд: Tripp Lite Страницы: 2

Бренд: Tripp Lite Страницы: 2

Бренд: Cisco Страницы: 60

Linksys BEFVP41 v2

Бренд: Cisco Страницы: 83

Catalyst 2900 Series XL

Бренд: Cisco Страницы: 138

Бренд: Cisco Страницы: 92

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды