Delta Tau ACC-72EX Скачать руководство пользователя страница 21 | Manualshive

Страница: 21 / 146

background image

ACC-72EX User Manual

DPRAM Memory Map

21

DPRAM MEMORY MAP

Below is the standard memory map of address offsets found in the DPRAM of the ACC-72EX module.
Start and end addresses for each of the memory blocks are specified both in Hilscher offset (0x notation
for hexadecimal) and Turbo PMAC offset ($ notation for hexadecimal) notation. The memory map shown
here is the standard memory map. Different COMX modules may have different memory maps. Please
refer to the Hilscher manual for each COMX module for detailed information.

These registers should be read from and written to using M-Variables which point to the lower 16 bits of
the X/Y-memory with an offset from the base address that is configured with E3. Handshake and System
registers are common between all protocols, and others can be auto-generated using the “ACC-72EX
Setup Assistant” software.

$0000 /

$000C /

$002C /

$002E /

$0030 /

$0040 /

$0060 /

$0080 /

$0080 /

$0081 /

$0082 /

$0083 /

$0084 /

$0085 /

$0086 /

$0087 /

$0088 /

$00C0 /

$00C0 /

$00C2 /

$00C4 /

$00D4 /

$0140 /

$02D0 /

$0460 /

$0470 /

$0480 /

$04C0 /

$0A60 /

$1000 /

$0000 /

$0080 /

$00C0 /

$1000 /

$4000 /

«
...
19
20
21
22
23
...
»

Содержание ACC-72EX



















































































































































Отзывы:

Нет отзывов

Похожие инструкции для ACC-72EX

Бренд: Vanguard Страницы: 4

Бренд: Zonet Страницы: 8

Бренд: dixell Страницы: 4

NJ220 - IntelliJack Switch

Бренд: 3Com Страницы: 82

Conel UR5i v2 Libratum

Бренд: B&B Electronics Страницы: 32

SteelCentral NetExpress

Бренд: Riverbed Страницы: 38

Бренд: Tbus Страницы: 25

Бренд: Faderfox Страницы: 10

SABVISION NVR32

Бренд: SAB Страницы: 29

Elinx ESW200 Series

Бренд: B&B Electronics Страницы: 20

Бренд: AMX Страницы: 2

Бренд: CalAmp Страницы: 115

Бренд: PairGain Страницы: 80

Бренд: Idis Страницы: 18

Бренд: Paradyne Страницы: 74

AirBridge VS-YOFIMN-000

Бренд: Vivint Страницы: 2

Бренд: Tenda Страницы: 82

Бренд: National Instruments Страницы: 147

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды