Warning
Please read this instruction sheet carefully before use and follow the sheet to operate TAP-CN01//02/03 in order to
prevent damages on the device or injuries to staff.
Switch off the power before wiring.
This instruction only provides introductory information on electrical specifications, functions, wiring,
trouble-shooting and peripherals for TAP-CN01/02/03.
TAP-CN01/02/03 is an OPEN-TYPE device and therefore should be installed in an enclosure free of airborne dust,
humidity, electric shock and vibration. The enclosure should prevent non-maintenance staff from operating the
device (e.g. key or specific tools are required to open the enclosure) in case danger and damage on the device may
occur.
In order not to damage it, only qualified professional staff familiar with the structure and operation of
TAP-CN01/02/03 can install, operate, wire and repair it.
DO NOT connect input AC power supply to any of the I/O terminals; otherwise serious damage may occur. Check all
the wiring again before switching on the power and DO NOT touch any terminal when the power is switched on.
Introduction
Thank you very much for choosing Delta TAP-CN01/02/03 distribution box. TAP-CN01/02/03 is the distribution
box for the connection of main cable and sub cable in DeviceNet or CANopen. TB1 and TB2 are for connecting
main cables, and TB3 ~ TB5 are for connecting sub cables. TAP-CN01/02/03 formulates a termination
resistance, which is switched by the setup switch.
Nameplate Explanation
VX.XXXX
MADE IN XXXXXX
R T U D E N T 0 0 T 7 2 0 0 0 0 1
MADE IN XXXXXX
CN010000W7250001
Model name
Barcode, Serial No.
Version
Serial No. Explanation
CN0X000
W
0001
0
7 25
Production No.
Production week
Production year (2007)
Production plant (W: Wujiang T: Taoyuan)
Version No.
Model name
Product Profile & Outline
1
DeviceNet/CANopen main cable connector
2
DeviceNet/CANopen main cable connector
3
DeviceNet/CANopen sub cable connector
4
Termination resistance setup switch
5
121
Ω
termination resistance
1
2
3
4
5
6
6 6 .5 0 [2 .62 ]
8
7
.0
0
[3
.4
3
]
Unit: mm
6
DIN rail
ENGLISH
1
DeviceNet/CANopen main cable connector
2
DeviceNet/CANopen main cable connector
3
DeviceNet/CANopen sub cable connector
4
DeviceNet/CANopen sub cable connector
5
DeviceNet/CANopen sub cable connector
6
Termination resistance setup switch
7
121
Ω
termination resistance
1
2
3
4
5
6
7
8
96.50[ 3.80]
9
7
.0
0
[3
.4
3
]
Unit: mm
8
DIN rail
1
DeviceNet/CANopen main cable connector
2
DeviceNet/CANopen main cable connector
3
DeviceNet/CANopen sub cable connector
4
DeviceNet/CANopen sub cable connector
5
DeviceNet/CANopen sub cable connector
6
Termination resistance setup switch
7
121
Ω
termination resistance
5
6
7
8
1
2
3
4
66.50[ 2.62]
6
6
.5
0
[2
.6
2
]
Unit: mm
8
DIN rail
Specifications
Electrical Specifications
DeviceNet
Voltage: 11 ~ 25V DC (supplied by the power cable in the network)
Environment
Operation/Storage
Operation: 0ºC ~ 55ºC (temperature), 50 ~ 95% (humidity), pollution degree 2
Storage: -25ºC ~ 70ºC (temperature), 5 ~ 95% (humidity)
How to Install
①
Use efficient tool to peel the communication cable
for approx. 30mm. DO NOT damage the shielded
cable while peeling.
App rox. 3 0m m
②
Peel off the metallic shielded net and foil and you
will see 2 power cables (in red and black), 2 signal
cables (in blue and white) and 1 shielded cable.
Shielded cable
③
Peel off the exterior metallic shielded net, foil and
the plastic cover of the power cable and signal cable
in proper length.
④
Insert the peeled communication cables into the
holes in the connector in correct order.
Black (V-)
Blue (CAN_L)
Shielded cable (CAN_SHLD)
Red (V+)
White (CAN_H)
⑤
Tighten the screws on the connector by a slotted
screwdriver, and fix the communication cables in
the holes in the connector.
Screw by a slotted screwdriver.
⑥
Use standard 35mm DIN rail.
⑦
Mount TAP-CN01/CN02/CN03 onto the DIN rail.
OF F
OF F
OF F
TAP-C N01
TAP-C N02
TAP -CN0 3
⑧
Insert the connectors into TAP-CN01/CN02/CN03.
Insert the connector into
TAP-CN01 terminal.
Insert the connector into
TAP-CN02 terminal.
Insert the connector into
TAP-CN03 terminal.
Notes:
1.
Use only wires specifically designed for DeviceNet/CANopen for wiring.
2.
The terminal screws shall be tightened to 5.18 kg-cm (4.5 in-lbs).
3.
DO NOT place the signal cable and power cable in the same wiring circuit.
Electrical Circuit
TAP-CN01
TAP-CN02
T
B
1
T
B
2
T
h
ic
k
C
a
b
le
T
h
ic
k
C
a
b
le
V+
V+
H
H
S
S
L
L
V-
V-
V+
H
S
L
V-
1
2
1
¿
TB3
Thin Cable
TB1
TB2
TB5
TB3
TB4
Thick Cable
Thick Cable
Thin Cable
Thin Cable
V+
V+
V+
H
H
H
S
S
S
L
L
L
V-
V-
V-
V+
V+
H
H
S
S
L
L
V-
V-
1
2
1
¿
TAP-CN03
T
B
1
T
B
2
T
h
ic
k
C
a
b
le
T
h
ic
k
C
a
b
le
V+
V+
H
H
S
S
L
L
V-
V-
1
2
1
¿
TB 3
TB4
TB5
8
8
7
7
6
6
5
5
4
4
3
3
2
2
1
1
8 76 5 4 3 2 1
Thin Cable
Thin Cable
Thin Cable
Components
DeviceNet/CANopen Connector
To connect with the DeviceNet/CANopen network, use the connector enclosed with TAP-CN01/02/03 or any
connectors you can buy in the store for wiring.
PIN
Signal
Description
V-
V-
0V DC
L
CAN_L
Signal-
S
SHIELD
Shielded cable
H
CAN_H
V+
V+
24V DC
V-
L
S
H
V+
PIN
Signal
Description
1
CAN_H
2
CAN_L
Signal-
3
CAN_GND
0V DC
4
RESE_1
Reserved
5
RESE_2
Reserved
6
CAN_SHLD
Shielded cable
7
CAN_GND
0V DC
8
CAN_V+
24V DC
1
2
3
4
5
6
7
8
Termination Resistance Setup Switch
O N
O FF
The termination resistance switch is used for determining whether the resistance is valid.
ON = valid; OFF = invalid.
Termination Resistance
TAP-CN01/CN02/CN03 formulates a 121
Ω
termination resistance.
Connection Example
Establishing a network through TAP-CN01/CN02/CN03:
TAP-CN02
TAP-CN01
TAP-CN03
Main cable
Main cable
Main cable
Sub cable
Sub cable
Sub cable
S
u
b
c
a
b
le
S
u
b
c
a
b
le
S
u
b
c
a
b
le
①
To install TAP-CN01/CN02/CN03 in the starting point or end of the network, you have to switch ON the
termination resistance. To install TAP-CN01/CN02/CN03 in the middle of the network, you have to switch
OFF the termination resistance.
②
When using TAP-CN01/CN02/CN03 to establish a DeviceNet/CANopen network, the sub cable cannot be
longer than 6m.
注意事項
請務必在使用之前仔細閱讀本使用手冊，並按照本手冊指示進行操作，以免造成產品受損，或導致人員受傷。
實施配線，務必關閉電源。
本使用說明書僅提供電氣規格、功能規格、安裝配線、故障排除及周邊裝置部分說明。
本機為開放型
(OPEN TYPE)
機殼，因此使用者使用本機時，必須安裝於具防塵、防潮及免於電擊
/
衝擊意外
的外殼配線箱內。另必須具備保護措施
(
如：特殊的工具或鑰匙才可打開
)
，防止非維護人員操作或意外衝擊
本體，造成危險及損壞。請勿在上電時觸摸任何端子。
為避免損壞本產品，只有合格且熟悉本產品結構及操作的專業人員才可進行本產品的安裝、操作、配線及維
護。
交流輸入電源不可連接於輸入
/
輸出信號端，否則可能造成嚴重損壞。請在上電前再次確認電源配線，且請勿
在上電時觸摸任何端子。本體上的接地端子。
產品簡介
謝謝您使用台達
TAP-CN01/CN02/CN03
分接盒。
TAP-CN01/CN02/CN03
定義為
DeviceNet
和
CANopen
分接盒，
用於
DeviceNet
或者
CANopen
主幹線與分支線的連接，
TB1
與
TB2
用於連接主幹線，
TB3 ~ TB5
用於連接分支
線。
TAP-CN01/CN02/CN03
集成一個
121
歐姆的終端電阻，並通過
SW
開關來切換是否有效。
銘牌說明
銘牌說明
銘牌說明
銘牌說明
VX.XXXX
MADE IN XXXXXX
RT UDENT0 0T7 2 0 0 0 0 1
MADE IN XXXXXX
CN 010 000W 725 000 1
產品型號
管理條碼序號
版本
序號說明
序號說明
序號說明
序號說明
CN0X000
W
0001
0
7 25
製造序號
生產週次
生產年份（2007年）
製造工廠（W： 吳江廠 T：桃園廠）
版本序號
生產機種
產品外觀及各部介紹
產品外觀及各部介紹
產品外觀及各部介紹
產品外觀及各部介紹
1
DeviceNet/CANopen
主幹線通訊連接器
2
DeviceNet/CANopen
主幹線通訊連接器
3
DeviceNet/CANopen
分支線通訊連接器
4
終端電阻設置開關
5
121
Ω終端電阻
1
2
3
4
5
6
66. 50[2.62]
8
7
.0
0
[3
.4
3
]
尺寸單位：
mm
6
DIN
軌槽
繁體中文
繁體中文
繁體中文
繁體中文
1
DeviceNet/CANopen
主幹線通訊連接器
2
DeviceNet/CANopen
主幹線通訊連接器
3
DeviceNet/CANopen
分支線通訊連接器
4
DeviceNet/CANopen
分支線通訊連接器
5
DeviceNet/CANopen
分支線通訊連接器
6
終端電阻設置開關
7
121
Ω終端電阻
1
2
3
4
5
6
7
8
96.50[ 3.80]
9
7
.0
0
[3
.4
3
]
尺寸單位：
mm
8
DIN
軌槽
功能規格
電氣規格
電氣規格
電氣規格
電氣規格
DeviceNet
電壓規格：
11 ~ 25V DC
（由網路中的電源線提供）
環境規格
環境規格
環境規格
環境規格
操作
/
儲存環境
操作：
0ºC ~ 55ºC
（溫度）、
50 ~ 95%
（濕度）、污染等級
2
儲存：
-25ºC ~ 70ºC
（溫度）、
5 ~ 95%
（濕度）
安裝說明
①
請使用專業工具將通訊電纜剝開大約
30mm
，在剝線過程
中注意不要損壞遮蔽線。
大約 30mm
②
剝開外層的金屬遮蔽網和鋁箔，你會看到
2
根電源線（紅
色和黑色）、
2
根信號線（藍色和白色）、
1
根遮蔽線。
遮蔽線
③
去除外層的金屬遮蔽網和鋁箔，然後剝去電源線以及信號
線的塑膠表皮，剝開的長度要適當。
1
DeviceNet/CANopen
主幹線通訊連接器
2
DeviceNet/CANopen
主幹線通訊連接器
3
DeviceNet/CANopen
分支線通訊連接器
4
DeviceNet/CANopen
分支線通訊連接器
5
DeviceNet/CANopen
分支線通訊連接器
6
終端電阻設置開關
7
121
Ω終端電阻
5
6
7
8
1
2
3
4
66.50[ 2.62]
6
6
.5
0
[2
.6
2
]
尺寸單位：
mm
8
DIN
軌槽
