Delta Electronics BX12.6AC100 страница 39 Скачать руководство пользователя

Страница: 39 / 68

3.13 Installation of BX12.6_AC100

- Before expansion battery pack, please power OFF the unit entirely to avoid risk

of electrical shock.

- Please check the battery pack regularly. If there are any impaired or loose parts,

please contact your installer. Ensure that there are no fallen objects.

- Please do not remove all the rubber covers on BX6.3_AC100 if BX6.3_EX100

is not installed.

For the higher capacity system - BX12.6_AC100, BX6.3_AC100 should be installed

with the BX6.3_EX100 as the following instruction.

1. Connect positive/negative cable from BX6.3_EX100 to BX6.3_AC100

2. Connect Communication cable (3 wires) from BX6.3_EX100 to BX6.3_AC100

3. Connect grounding cable from BX6.3_EX100 to BX6.3_AC100.

Recommended cable length (about 1000mm) / 12AWG with ring terminal lug.

Please make sure the polarity is properly connected as shown below.

Figure 3-17 : Expanding the Battery Pack with DC(BT+/-) cables

DANGER: ELECTRICAL HARZARD!!

①

Uart signal

②

Relay signal

③

Heater signal

① ② ③

Ground

ATTENTION

* BT+/-:

Recommended cable length (about 1000mm) / 12AWG

BT+

BT-

BX6.3_EX100

BX6.3_AC100

Installation

Содержание BX12.6AC100





































































Результаты поиска

Содержание BX12.6AC100

Отзывы:

Похожие инструкции для BX12.6AC100

Бренды по названию

Популярные бренды

Delta Electronics BX12.6AC100, Руководство по эксплуатации и установке

Результаты поиска

Содержание BX12.6AC100

Отзывы:

Похожие инструкции для BX12.6AC100

Бренды по названию

Популярные бренды