background image

3.4 Mechanical Installation

- Please check the space for installation which meets the recommended location.

- Remember that DELTA will in not responsible for damage resulting from

  BX6.3_AC100 falling due to insufficient mounting strength.

ATTENTION

This AC Storage System is designed for ground-mounted.
Please ensure that the installation is perpendicular to the floor.
Please follow the instructions as shown from 

Figure 3-5

 through 

3-8

.

Please make sure there is enough space for the AC Storage System, especially
reverse side of the AC Storage System (heatsink requirement).

WARNING !

- BX6.3_AC100 should be installed by a trained and experienced installer designated

  by the retailer.

- Having the product installed by a non-specialized installer is very dangerous and

  can cause damage or injury.

Figure 3-5 : Recommended Installation Space

100 mm

90°

>30 mm*

100 mm

100 mm

100 mm

* Please refer to regulation AS/NZS 5139:2019 for detail installation space requirement. 

  To avoid extra fireproof cement sheeting installation requirement, it is recommended to keep at

  least 300 mm between the wall and BX.

24

Installation

Содержание BX12.6AC100





































































Отзывы: