background image

TYXIA 411

Lighting receiver switch

Installation and User Guide

Device complying with the requirements of the

R&TTE 1999/5/EC directives

*2701934_rev1*

Because of changes in standards and equipment, the characteristics given in the
text and the illustrations of this document are not binding unless confirmed by
Delta Dore.

DELTA DORE 

Bonnemain - 35270 COMBOURG - France

E-mail : [email protected]

• Carefully read these instructions prior to instal-

lation.

• The unit must be installed in compliance with

currently applicable standards.

• Always switch off the mains before installing or

servicing the unit.

• Do not attempt to repair the unit yourself; an

after-sales service is available.

• Check that the fastenings are suited to the sur-

face that the unit will be attached to (plaster-
board, brick, etc.).

• The diagrams provided are simplified for grea-

ter clarity. The protective units and other
accessories required by the standards are not
illustrated.

Standard UTE NF C15-100 and good practice
must be complied with. Connected or nearby
equipment must not generate excessive inter-
ference (directive 2004/108/EEC).

Warnings

Your unit comes with a plastic protection that must
be removed when work is complete (for example
after painting), before replacing the cover plate
(Delta Dore brand located in the lower right).

Location

The receiver must be fitted on a flush-mounted box
(Ø 65 mm) that will receive the live and neutral
wires.

Connecting and mounting the product

Connect the product
(see adapted connec-
tion according to your
application), then posi-
tion it by orienting the
terminal upwards.
Secure it by tightening
the screws without for-
cing them.

Plastic 
protection

Installation

Operation with a transmitter
associated TYXIA or TYDOM

Press the receiver button 
until the LED flashes (~3 seconds).
2 possible choices.
Slow flashing: simple lighting mode
Rapid flashing: remote control switch mode.

Press the receiver  

button to pass from one

rate of flashing to the other.
Select the rapid flashing.

IMPORTANT: The receiver is delivered in simple
lighting mode. To use it in remote control switch
mode, it must be associated with a transmitter.
The remote control switch mode can only be
controlled by a 

(TYXIA) or 

(TYDOM 200

button).

or

(status being modified)

Connection

Operating the TYXIA 411

Pressing the  

button changes the current state

(on or off).

TYXIA 411

Remote control switch

L

N

L
N

230 V
50 Hz

T L R N N

IMPORTANT: 
Do not connect 
terminal 3 for 
this application.

Remote control switch mode

Connection

Operating the TYXIA 411

Pressing the 

button changes the current state

(on or off).

L

T L R N N

N 230 V

50 Hz

Existing

switch

TYXIA 411

Two-way switch mode

On the transmitter, press and hold the 

button

for 5 seconds. The LED will light up, go out, then
light up again. Release.

Check that the receiver’s LED is no longer flashing.

The transmitter 

button is associated with

the receiver in remote control switch mode.

To link a TYXIA 411 with a TYDOM 200, please
refer to the TYDOM 200 guide.

On the transmitter, press and hold the 

button

for 5 seconds. The LED will light up, go out, then
light up again. Release.
Check that the receiver’s LED is no longer flashing.

The 

transmitter button is linked with the

receiver in two-way switch mode.

To link a TYXIA 411 with a TYDOM 200, please
refer to the TYDOM 200 guide.

Operation with a transmitter
associated TYXIA or TYDOM

Press the receiver button 

until the LED flashes

(~3 seconds).
2 possible choices.
Slow flashing: two-way switch mode
Rapid flashing: remote control switch mode (unused).
Press the receiver 

button to pass from one rate

of flashing to the other.
Select the slow flashing.

IMPORTANT: he two-way switch mode can only be
controlled by a 

(TYXIA) or 

button 

(TYDOM 200).

or

(status being modified)

Connection

Operating the TYXIA 411

Pressing the 

button changes the current state

(on or off).

L

N 230 V

50 Hz

T L R N N

TYXIA 411

Simple lighting mode

Associating a 

button (scenario)

On the receiver, set the appliance to the required
status (e.g. light off), then press the receiver button

until the LED flashes (~3 seconds).

2 possible choices.
Slow flashing: simple lighting mode
Rapid flashing: remote control switch mode (unused).
Press the receiver 

button to pass from one rate

of flashing to the other.
Select the slow flashing.

On the transmitter, press and hold the 

button

down for approximately 5 seconds. The LED will light
up, go out, then light up again. Release.
Check that the receiver’s LED is no longer flashing.

The transmitter 

button is associated with the

receiver.

button can control different receivers simulta-

neously (roller blinds, dimmer, simple lighting, etc.).

Associate buttons

Press the receiver button

until the LED flashes

(~3 seconds).

2 possible choices.
Slow flashing: simple lighting mode
Rapid flashing: remote control switch mode (unused).
Press the receiver 

button to pass from one rate

of flashing to the other.
Select the slow flashing.

On the transmitter, simultaneously press and hold
the and buttons 

for 

approximately 

5

seconds, until the LED comes on.
Release.
Check that the receiver’s LED is no longer flashing.
The transmitter buttons 

and 

are associated

with the receiver.

Associating a 

button

Press the receiver button 

until the LED flashes

(~3 seconds).

2 possible choices.
Slow flashing: simple lighting mode
Rapid flashing: remote control switch mode (unused).
Press the receiver 

button to pass from one rate

of flashing to the other.
Select the slow flashing.

On the transmitter, press and hold the 

button

down for approximately 5 seconds. The LED will light
up, go out, then light up again. Release.
Check that the receiver’s LED is no longer flashing.
The transmitter 

button is associated with the

receiver.

Simple lighting mode with an associated TYXIA transmitter

The simple lighting mode can be controlled by a
TYXIA transmitter (transmitter switch, key ring
remote control, etc.).

(recommended for controlling 

exterior lighting)

OFF

ON

OFF

ON

OFF

ON

Either is possible, depending on the scenario.

or

The receiver can record up to a maximum of 8
associations (buttons, transmitters, etc.).

The receiver is compatible with:

incandescent lamps 

(1000 W), 230V halogen

lamps (1000 

W), 

low-consumption 

lamps

(300 W), halogens with electronic transformers

(300 W) and 230V halogen lamps with TBT ferro-

magnetic transformer (300 W).

The receiver is incompatible with:
fluorescent lamps, motors and controlling hi-fi or
video products.

Отзывы: