Delta Controls eZFC-424R4-24 Скачать руководство пользователя страница 52

Страница: 52 / 85

eZFC-424R4-24 Application Guide
Edition 2.6

Page 51 of 84

Setpoints Tab

What is the Setpoints Tab?

Use the Setpoints tab on the enteliZONE configuration page to enter the temperature setpoints for

the system controlled by the enteliZONE controller.

The absolute minimum value for all occupied and unoccupied setpoints is 10°C (50°F). The

absolute maximum value is 30°C (86°F).

To change the temperature units, go to the General tab on the configuration page.

Space Temperature Setpoints

This section defines each setpoint on the configuration page.

Occupied Heating Setpoint (OccHeatingSetpoint)

When the controller is in occupied mode, heating is turned on when the space temperature drops

below this setpoint.

Unoccupied Heating Setpoint (UnOccHeatingSetpoint)

When the controller is in unoccupied mode, heating is turned on when the space temperature

drops below this setpoint.

Occupied Cooling Setpoint (OccCoolingSetpoint)

When the controller is in unoccupied mode, cooling is turned on when the space temperature rises

above this setpoint.

Unoccupied Cooling Setpoint (UnOccCoolingSetpoint)

When the controller is in unoccupied mode, cooling is turned on when the space temperature rises

above this setpoint.

Occupied Setpoint Offset Range (OccSetpointOffsetRange)

The offset range available at a LINKnet stat interface or a hardwired setpoint adjustment input. The

offset is added to the Occupied Heating and Cooling setpoints to set the values of the Current

Heating and Cooling setpoints in occupied mode.

For example, when you enter a value of 2.0, the offset range is ±2.0 from the heating setpoint and

±2.0 from the cooling setpoint.

Содержание eZFC-424R4-24






















































































Результаты поиска

Содержание eZFC-424R4-24

Отзывы:

Бренды по названию

Популярные бренды

Delta Controls eZFC-424R4-24, Инструкция по применению

Результаты поиска

Содержание eZFC-424R4-24

Отзывы:

Бренды по названию

Популярные бренды