background image

7

Freezing protection

With the knob of the thermostat (

B

) in position   and one of 

the power levels selected, the appliance will maintain the room 

at a temperature of about 41°F (5°C) preventing freezing with 

minimum energy consumption. 

Models with fan

The appliance is equipped with a fan that provides even more 

rapid and uniform heating. 

To start this function, turn the power selector (

) to Max   .

Models with 24-hour timer

When the appliance is connected to the power supply the timer 

is always active so as to stay synchronized with the local time. 

To operate the appliance without timer, position the timer 

slider (

) to 

 . 

To operate the appliance at the times set, position the timer 

slider to 

  (Fig. 1) and proceed as follows:

•  Check the time on your clock or watch. If it is 10.00 for 

example, turn the numbered programmer disk until the 

number 10 coincides with the pointer marked on the 

programmer device.

•  Set the periods of time during which you want the 

appliance to operate by pushing the teeth outwards (see 

figure). Each tooth corresponds to a period of 30 min. At 

the end of the procedure, the sectors corresponding to the 

periods of operation will be visible.

•  In this way, the appliance will function automatically 

each day at the times set. (Important: the appliance must 

always be connected to the power supply).

•  To modify the settings, return the teeth to the initial 

position and set the new operating periods.

•  To turn the appliance off, turn the power selector  to "0".

SAFETY FUNCTIONS

-  

Safety device:

 The appliance is fitted with a safety 

cutoff device which will switch the appliance off in case 
of accidental overheating. To reset the cutoff, disconnect 
the plug from the power supply for a few minutes, 
remove the cause of overheating, then reconnect the 
appliance. If this abnormal situation happens several 
times, contact customer service.

-  

Tip-over safety device:

 This device turns the appliance 

off if it falls over or is positioned inappropriately in such 
a way as to jeopardize safety. The appliance resumes 
operation a few seconds after being placed in an upright 
position again.

MAINTENANCE

Before carrying out any maintenance, disconnect the appliance 

from the power supply and wait for it to cool down completely. 

This appliance requires no particular maintenance. 

It is sufficient to remove dust with a soft, dry cloth. Never use 

abrasive powders or solvents. If necessary remove areas of 

concentrated dirt with a vacuum cleaner. 

PROBLEM

CAUSE

SOLUTION

The appliance doesn’t 

work

The plug is not inserted properly into the 

power socket or the socket switch is off.

The power selector is in the ”0” position.

The thermostat is set too low. 

Timer setting.

The tip-over switch has been activated.

Insert the plug into the power socket and 

switch on if necessary.

 

Move the power selector to position MIN, MED, 
MAX or MAX   .

Turn the thermostat knob clockwise to higher 

settings until the heater restarts. 

Make sure the timer is correctly set to local 

time and check the position of the teeth.

Make sure the appliance is standing upright 

on a flat surface, if the problem persists 

contact our toll free number to assist you.

The alarm sound and the 

appliance doesn't work

Check for any obstruction.

Remove the obstruction, disconnect the 

power plug of the heater and let the appliance 
cool down. If the appliance doesn't work 
please contact the De longhi toll free number.

TROUBLESHOOTING

Содержание HSX3315FTS









Отзывы: