DeLonghi EUROCHEF - PRO страница 13 Скачать руководство пользователя

Страница: 13 / 16

Air-2

EUROCHEF - PRO WALL HOOD

• Use screws removed in Step 2 to re-install Filter Frame, per

photograph.

STEP 7:

TIGHTEN - HANGING SCREWS

STEP 8:

RE-INSTALL THE FILTER FRAME

•

With Filter Frame still removed from Step 2

•

Adjust hood up to eliminate any gaps at ceiling. Tighten
hanging screws.

•

Add (2) more security Washers at wood bracket.

•

IMPORTANT

: If Installing optional Backsplash Kit install this

kit BEFORE installing wall anchors
(see instruction with kit)

Install Bottom Wall Anchors

•

Drill 1//8" pilot holes into the two lower mounting holes. Enlarge
the holes if they did not enter studs to 3/8".

•

Install (2) or (3) wall anchors at bottom of hood.

•

Remove anchor screws and add a flat washer provided. Drive
screws into anchors and tighten.

•

If a Wood Stud was discovered at wall anchor locations use
80mm Wood Screw supplied with Washer (instead of Wall
anchor). Drive screws and tighten.

Содержание EUROCHEF - PRO

















Результаты поиска

Содержание EUROCHEF - PRO

Отзывы:

Похожие инструкции для EUROCHEF - PRO

Бренды по названию

Популярные бренды

DeLonghi EUROCHEF - PRO, Руководство по установке

Результаты поиска

Содержание EUROCHEF - PRO

Отзывы:

Похожие инструкции для EUROCHEF - PRO

Бренды по названию

Популярные бренды