Dell Vostro 3681 Скачать руководство пользователя страница 8 | Manualshive

Страница: 8 / 64

Dell Vostro 3681 Скачать руководство пользователя страница 8

CAUTION:

Do not lift greater than 50 pounds. Always obtain additional resources or use a mechanical lifting device.

1. Get a firm balanced footing. Keep your feet apart for a stable base, and point your toes out.
2. Tighten stomach muscles. Abdominal muscles support your spine when you lift, offsetting the force of the load.
3. Lift with your legs, not your back.
4. Keep the load close. The closer it is to your spine, the less force it exerts on your back.
5. Keep your back upright, whether lifting or setting down the load. Do not add the weight of your body to the load. Avoid twisting your

body and back.

6. Follow the same techniques in reverse to set the load down.

After working inside your computer

About this task

After you complete any replacement procedure, ensure that you connect any external devices, cards, and cables before turning on your
computer.

Steps

1. Connect any telephone or network cables to your computer.

CAUTION:

To connect a network cable, first plug the cable into the network device and then plug it into the

computer.

2. Connect your computer and all attached devices to their electrical outlets.
3. Turn on your computer.
4. If required, verify that the computer works correctly by running

ePSA diagnostics

.

8

Working on your computer

«
...
6
7
8
9
10
...
»

Содержание Vostro 3681

































































Отзывы:

Нет отзывов