Dell Vostro 3490 Скачать руководство пользователя страница 25

Страница: 25 / 96

Next steps

1. Connect the battery cable to the connector on the system board.
2. Replace the

base cover

3. Replace the

SD memory card

4. Follow the procedure in

after working inside your computer

Coin-cell battery

Removing the coin-cell

Prerequisites

1. Follow the procedure in

before working inside your computer

2. Remove the

SD memory card

3. Remove the

base cover

4. Disconnect the battery cable from the connector on the system board.

Steps

1. Using a plastic scribe, gently pry the coin-cell battery out of the slot on the I/O board [1].
2. [2].

Installing the coin-cell battery

Steps

1. With the positive-side facing up, insert the coin-cell battery into the battery socket on the I/O board [1].
2. Press the battery until it clicks into place [2].

Removing and installing components

Содержание Vostro 3490

































































































Результаты поиска

Содержание Vostro 3490

Отзывы:

Похожие инструкции для Vostro 3490

Бренды по названию

Популярные бренды

Dell Vostro 3490, Руководство по обслуживанию

Результаты поиска

Содержание Vostro 3490

Отзывы:

Похожие инструкции для Vostro 3490

Бренды по названию

Популярные бренды