Dell USC Скачать руководство пользователя страница 16

Страница: 16 / 132

Introduction

What’s new in USC/USC-LCE 1.5

The new features are:

• Backup and Export server profile
• Import server profile
• View and export factory shipped inventory
• Configure and upgrade firmware for Converged Network Adapters (CNA)

cards. Supported on the following CNA card:
Broadcom:
–

M710HD Dual Port 10Gig 57712 NDC

• Software RAID configuration

• Enhancement to the RAID configuration feature — Virtual disk slicing

support

• Driver packs support for new operating systems

. For more information,

see

USC/USC-LCE – Supported Dell Systems and Operating Systems

section in the

Dell Systems Software Support Matrix

available at

support.dell.com/manuals

1. Indicates the newly introduced feature for USC.

Upgrading to USC or USC-LCE

Depending on the system, you can upgrade from a Baseboard Management

Controller (BMC) to an Integrated Dell Remote Access Controller 6

(iDRAC6) Express or an iDRAC6 Enterprise card; this hardware upgrades the

USC to USC-LCE. See

Updating Platform

for more information.

NOTE:

You can upgrade Dell systems series

y21x-y51x

to USC-LCE. See the

Hardware Owner’s Manual

for more information.

Содержание USC





































































































































Результаты поиска

Содержание USC

Отзывы:

Dell USC, Руководство пользователя, Страница: 16 / 132

Результаты поиска

Содержание USC

Отзывы: