manualshive.com logo in svg

Dell PowerEdge M600, Руководство владельца оборудования, Страница: 93 / 236

Поделиться
Скачать
Dell PowerEdge M600 Скачать руководство пользователя страница 93

Using the System Setup Program

93

5

Confirm that

 Not Enabled

 is displayed for the 

System Password

 option. 

If 

Not Enabled

 is displayed for the 

System Password 

option, the system 

password has been deleted. If 

Enabled 

is displayed for the 

System 

Password

 option, press the <Alt><b> key combination to restart the 

system, and then repeat steps 2 through 5.

Using the Setup Password

Assigning a Setup Password

You can assign (or change) a setup password only when the 

Setup Password

 

option is set to 

Not Enabled

. To assign a setup password, highlight the

 Setup 

Password

 option and press the <

+>

 or

 <–>

 key. The system prompts you to 

enter and verify the password. 

 

NOTE: 

The setup password can be the same as the system password. If the two 

passwords are different, the setup password can be used as an alternate system 
password. However, the system password cannot be used in place of the setup 
password.

You can use up to 32 characters in your password.

As you press each character key (or the spacebar for a blank space), a 
placeholder appears in the field.

The password assignment is not case-sensitive. However, certain key 
combinations are not valid. To erase a character when entering your password, 
press <Backspace> or the left-arrow key.

After you verify the password, the 

Setup Password

 setting changes to 

Enabled

. The next time you enter the System Setup program, the system 

prompts you for the setup password.

A change to the 

Setup Password 

option becomes effective immediately 

(restarting the system is not required).

Operating With a Setup Password Enabled

If 

Setup Password

 is set to 

Enabled

, you must enter the correct setup 

password before you can modify most of the System Setup options. When 
you start the System Setup program, the program prompts you to enter a 
password.

Содержание PowerEdge M600













































































































































































































































Отзывы:

Нет отзывов