Dell PowerEdge M600 Скачать руководство пользователя страница 186 | Manualshive

Страница: 186 / 236

background image

186

Troubleshooting Your System

Troubleshooting Power Supply Modules

Problem

•

A power supply module is not operating properly

Action

NOTICE:

The power-supply modules are hot-pluggable. Remove and replace only

one power-supply module at a time in a system that is turned on. Leave a failed
power-supply module installed in the enclosure until you are ready to replace it.
Operating the system with a power-supply module removed for extended periods of
time can cause the system to overheat.

NOTE:

The 2360-W power supply modules require a 200–240 V power source to

operate. If they are plugged into 110-V electrical outlets, the power supply modules
do not power up.

1

Locate the faulty power supply module and check the indicators. See
Figure 1-11. The power supply's AC indicator is green if AC power is
available. The power supply's fault indicator is amber if the power supply is
faulty. If no indicators are lit, ensure that 208V AC power is available from
the PDU and that the power cable is properly connected to the power
supply module.

2

Install a new power supply. See "Installing a Power Supply Module" on
page 160.

NOTE:

After installing a new power supply, allow several seconds for the

system to recognize the power supply and determine whether it is working
properly. The power supply DC power indicator turns green if the power
supply is functioning properly. See Figure 1-11.

3

If none of the power supplies show a fault LED and the blades will not
power on, check the LCD display or CMC for status messages.

4

If the problem is not resolved, see "Getting Help" on page 217 for
information about obtaining technical assistance.

Troubleshooting Fan Modules

Problem

•

A fan is not operating properly

«
...
184
185
186
187
188
...
»

Содержание PowerEdge M600













































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для PowerEdge M600

EK-FC780 GTX Jetstream

Бренд: ekwb Страницы: 2

JetWeb JX2-PR0FI1

Бренд: Jetter Страницы: 67

Бренд: Belkin Страницы: 72

Бренд: Qlogic Страницы: 2

HHM Series HHM2411

Бренд: TDK Страницы: 2

Speedway Revolution

Бренд: impinj Страницы: 60

Бренд: IEI Technology Страницы: 3

Бренд: Eneo Страницы: 68

dspstak 21262sx

Бренд: Danville Signal Processing Страницы: 35

CNPS7000C Series

Бренд: ZALMAN Страницы: 8

Zypad WL15 Series

Бренд: Eurotech Страницы: 2

Бренд: Renesas Страницы: 746

Бренд: Ubiquiti Страницы: 13

VIGI NVR1004H-4P

Бренд: TP-Link Страницы: 2

Бренд: Nortel Страницы: 163

Бренд: Baracoda Страницы: 16

LEDWALL Optimizer HQ P2

Бренд: Gundermann VIDEOWALL Страницы: 12

Бренд: Raven Страницы: 33

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды