Dell PowerEdge M600 Скачать руководство пользователя страница 144 | Manualshive

Страница: 144 / 236

background image

144

Installing Blade Components

See your operating system documentation for more information on taking
the hard drive offline.

2

Open the hard-drive carrier handle to release the drive. See Figure 3-24.

3

Slide the hard drive out until it is free of the drive bay.

If you are permanently removing the hard drive, install a blank insert.

Shutdown Procedure for Servicing a Hard Drive

NOTE:

This section applies only to situations where the blade must be powered

down to service a hard drive. In many situations, the hard drive can be serviced
while the blade is powered on.

If you need to power off the blade to service a hard drive, wait 30 seconds
after the blade’s power indicator turns off before removing the hard drive.
Otherwise, the hard drive may not be recognized after the hard drive is
reinstalled and the blade is powered on again.

Configuring the Boot Drive

The drive or device from which the system boots is determined by the boot
order specified in the System Setup program (see "Using the System Setup
Program" on page 79.

Removing a Hard Drive From a Hard-Drive Carrier

Remove the four screws from the slide rails on the hard-drive carrier and
separate the hard drive from the carrier. See Figure 3-24.

Installing a Hard Drive In a Drive Carrier

1

Insert the hard drive into the hard-drive carrier with the connector end
of the drive at the back of the carrier. See Figure 3-24.

2

Align the screw holes on the hard drive with the holes on the hard-drive
carrier.

3

Attach the four screws to secure the hard drive to the hard-drive carrier.

«
...
142
143
144
145
146
...
»

Содержание PowerEdge M600













































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для PowerEdge M600

Бренд: TC Electronic Страницы: 55

Бренд: Dahua Страницы: 24

Бренд: RAK Страницы: 30

Бренд: EMCIS Страницы: 14

Бренд: TANDBERG Страницы: 3

Бренд: Z-Wave Страницы: 6

Бренд: Gearlinx Страницы: 23

Бренд: Icy Box Страницы: 2

Бренд: Stepper Motor Canada Страницы: 5

FiberTwist XGS2420

Бренд: Genexis Страницы: 7

Бренд: Moxa Technologies Страницы: 8

Бренд: NEC Страницы: 114

Бренд: Commell Страницы: 17

Бренд: IBM Страницы: 78

Бренд: Zhone Страницы: 494

ForeFront 2616RC

Бренд: Patton electronics Страницы: 80

Бренд: SeaLevel Страницы: 19

Бренд: Tachosys Страницы: 15

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды