manualshive.com logo in svg

Dell PowerEdge C4130, Руководство пользователя

Dell PowerEdge C4130 - мощный серверный узел, идеально подходящий для вычислительных нагрузок. У вас есть возможность бесплатно скачать Руководство пользователя на manualshive.com. Этот бесплатный ресурс поможет вам освоиться с вашим новым оборудованием и использовать его на максимум его возможностей.

Поделиться
Скачать
background image

Installing a 1.8 inch uSATA SSD blank

Install the SSD blank if you are removing the SSD permanently or not replacing it immediately.

Prerequisites

Follow the safety guidelines listed in the Safety instructions section.

Steps

Insert the SSD blank into the SSD slot until the release button clicks into place.

Figure 53. Installing a 1.8 inch SSD blank

1.

SSD blank

Related Links

Safety instructions
Removing a 1.8 inch uSATA SSD blank

Removing a 1.8 inch uSATA SSD carrier

You need to remove the SSD carrier because the SSD is installed in the SSD carrier.

Prerequisites

CAUTION: Many repairs may only be done by a certified service technician. You should only 

perform troubleshooting and simple repairs as authorized in your product documentation, or as 

directed by the online or telephone service and support team. Damage due to servicing that is 

not authorized by Dell is not covered by your warranty. Read and follow the safety instructions 

that are shipped with your product.

1.

Follow the safety guidelines listed in the Safety instructions section.

2.

Using the management software, prepare the SSD for removal. Wait until the indicators on the SSD 

carrier signal that the SSD can be removed safely.
If the SSD is online, the green activity fault indicator flashes as the drive is turned off. When the SSD 
indicators are off, the SSD drive is ready for removal. For more information, see the documentation 
for the storage controller.

NOTE: The 1.8 inch uSATA SSDs are hot swappable only with software RAID S130. If your 

system supports software RAID S130 proceed to step 4. If not, continue with step 3.

3.

Turn off the system, including any attached peripherals.

4.

Disconnect the system from the electrical outlet and disconnect the peripherals.

130

Содержание PowerEdge C4130


























































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для PowerEdge C4130

Razberi V8 Core Manual And Getting Started Manual preview
V8
Бренд: Razberi Страницы: 113
IBM LS42 - BladeCenter - 7902 Service Manual preview
LS42 - BladeCenter - 7902
Бренд: IBM Страницы: 194
NAIM HDX-SSD - Quick Start Manual preview
HDX-SSD -
Бренд: NAIM Страницы: 16
IBM Flex System x440 Compute Node Installation And Service Manual preview
Flex System x440 Compute Node
Бренд: IBM Страницы: 584
Korenix AnyBus-X Installation Leaflet preview
AnyBus-X
Бренд: Korenix Страницы: 2
LTS LTAH103C Hardware Integration Manual preview
LTAH103C
Бренд: LTS Страницы: 5
Avaya Aura 5300 User Manual preview
Aura 5300
Бренд: Avaya Страницы: 119
Portwell PNA-3303 User Manual preview
PNA-3303
Бренд: Portwell Страницы: 21
Supero SUPERO SuperServer 6026TT-H6IBQRF User Manual preview
SUPERO SuperServer 6026TT-H6IBQRF
Бренд: Supero Страницы: 110
Supero SuperServer 6026TT-HIBQF User Manual preview
SuperServer 6026TT-HIBQF
Бренд: Supero Страницы: 112
Ablecom CE-HE130S4 Series User Manual preview
CE-HE130S4 Series
Бренд: Ablecom Страницы: 43
Supermicro SuperServer 5037C-i User Manual preview
SuperServer 5037C-i
Бренд: Supermicro Страницы: 88
I-O DATA FIDATA HFAS1-S10U Setup Manual preview
FIDATA HFAS1-S10U
Бренд: I-O DATA Страницы: 46
AXIOMTEK NA580 series User Manual preview
NA580 series
Бренд: AXIOMTEK Страницы: 76
Infrant Technologies ReadyNAS Duo User Manual preview
ReadyNAS Duo
Бренд: Infrant Technologies Страницы: 98
Fujitsu PRIMERGY BX620 S5 Options Manual preview
PRIMERGY BX620 S5
Бренд: Fujitsu Страницы: 50
Fujitsu PRIMERGY BX620 S4 Operating Manual preview
PRIMERGY BX620 S4
Бренд: Fujitsu Страницы: 81
Fujitsu PRIMERGY BX900 S1 Service Supplement Manual preview
PRIMERGY BX900 S1
Бренд: Fujitsu Страницы: 46

Бренды по названию

Популярные бренды

Загрузить еще бренды