Dell PowerEdge 700 Скачать руководство пользователя страница 53

Страница: 53 / 94

17.

Install the bezel. See "

Installing the Bezel

18.

Reconnect the system to the electrical outlet, and turn on the system and attached peripherals.

19.

Format and partition the hard drive. See the operating system documentation.

20.

If possible, restore the files to the drive.

If the problem persists, see "

Getting Help

Troubleshooting SATA Hard Drives

Troubleshooting a SATA Hard Drive Connected to the Integrated Drive Controller

Problem

Faulty hard drive.

Damaged or improperly connected hard-drive cables.

Action

Run the appropriate online diagnostic test. See "

Using Server Administrator Diagnostics

" in "Running System Diagnostics."

If the test fails, continue to the next step.

Enter the System Setup program and verify that the system is configured correctly. See "Using the System Setup Program" in your

User's Guide

Run the hard drive and SATA devices tests in the system diagnostics. See "

Running System Diagnostics

If the tests fail, continue to the next step.

Turn off the system and attached peripherals, and disconnect the system from the electrical outlet.

Remove the bezel. See "

Removing the Bezel

Stand the system upright.

Remove the cover. See "

Removing the Cover

Ensure that the hard-drive interface cable is properly connected to the drive and to the appropriate SATA port connector on the system board.

To identify the SATA port connectors, see

Figure A

-3

If the hard drive is the boot drive, ensure that the drive is configured and connected properly. See "

Configuring the Boot Drive

" in "Installing Drives."

10.

Ensure that the power cable is properly connected to the drive.

11.

Replace the cover. See "

Replacing the Cover

12.

Stand the system upright.

13.

Install the bezel. See "

Installing the Bezel

14.

Reconnect the system to the electrical outlet, and turn on the system and attached peripherals.

15.

Format and partition the hard drive. See the operating system documentation.

16.

If possible, restore the files to the drive.

NOTICE:

This troubleshooting procedure can destroy data stored on the hard drive. Before you proceed, back up all files on the hard drive.

NOTE:

If the SATA hard drive is used in a RAID configuration, see "

Troubleshooting a SATA Hard Drive in a RAID Configuration (When Available)

CAUTION:

See your

System Information Guide

for complete information about safety precautions, working inside the computer, and protecting

against electrostatic discharge.

Содержание PowerEdge 700































































































Результаты поиска

Содержание PowerEdge 700

Отзывы:

Похожие инструкции для PowerEdge 700

Бренды по названию

Популярные бренды

Dell PowerEdge 700, Инструкция по установке и устранению неисправностей

Результаты поиска

Содержание PowerEdge 700

Отзывы:

Похожие инструкции для PowerEdge 700

Бренды по названию

Популярные бренды