Dell PowerEdge 700 Скачать руководство пользователя страница 41

Страница: 41 / 94

Action

Turn off the system and any peripheral devices connected to the serial port.

Swap the serial interface cable with a working cable, and turn on the system and the serial device.

If the problem is resolved, replace the interface cable. See "

Getting Help

Turn off the system and the serial device, and swap the device with a comparable device.

Turn on the system and the serial device.

If the problem is resolved, replace the serial device. See "

Getting Help

If the problem persists, see "

Getting Help

Troubleshooting a USB Device

Problem

System message indicates a problem with a USB device.

Device connected to a USB port is not operating properly.

Action

Enter the System Setup program, and ensure that the USB ports are enabled. See "Using the System Setup Program" in your

User's Guide

Turn off the system and any USB devices.

Disconnect the USB devices, and connect the malfunctioning device to the other USB connector.

Turn on the system and the reconnected device.

If the problem is resolved, the USB connector might be defective. See "

Getting Help

If possible, swap the interface cable with a working cable.

If the problem is resolved, replace the interface cable. See "

Getting Help

Turn off the system and the USB device, and swap the device with a comparable device.

Turn on the system and the USB device.

If the problem is resolved, replace the USB device. See "

Getting Help

If the problem persists, see "

Getting Help

Troubleshooting a NIC

Problem

NIC cannot communicate with network.

Action

Run the appropriate online diagnostic test. See "

Using Server Administrator Diagnostics

" in "

Running System Diagnostics

Содержание PowerEdge 700































































































Результаты поиска

Содержание PowerEdge 700

Отзывы:

Похожие инструкции для PowerEdge 700

Бренды по названию

Популярные бренды

Dell PowerEdge 700, Инструкция по установке и устранению неисправностей

Результаты поиска

Содержание PowerEdge 700

Отзывы:

Похожие инструкции для PowerEdge 700

Бренды по названию

Популярные бренды