manualshive.com logo in svg

Dell PowerConnect J-8216, Руководство по оборудованию

Поделиться
Скачать
Dell PowerConnect J-8216 Скачать руководство пользователя страница 186

6.

Grasp the transceiver ejector lever and gently slide the transceiver approximately
0.5 in. (1.3 cm) straight out of the port.

CAUTION:

To avoid electrostatic discharge (ESD) damage to the

transceiver, do not touch the connector pins at the end of the transceiver.

7.

Using your fingers, grasp the body of the transceiver and pull it straight out of the port.

8.

Place the transceiver in the antistatic bag or on the antistatic mat placed on a flat,
stable surface.

9.

Place the dust cover over the empty port.

Figure 77: Removing a Transceiver from a J-EX Series Switch

Related

Documentation

Installing a Transceiver in a J-EX Series Switch on page 126

•

•

Optical Interface Support in J-EX8200 Switches on page 51

Disconnecting a Fiber-Optic Cable from a J-EX Series Switch

J-EX Series switches have field-replaceable unit (FRU) optical transceivers to which you
can connect fiber-optic cables.

Before you begin disconnecting a fiber-optic cable from an optical transceiver installed
in a J-EX Series switch, ensure that you have taken the necessary precautions for safe
handling of lasers (see “Laser and LED Safety Guidelines and Warnings for J-EX Series
Switches” on page 207).

Ensure that you have the following parts and tools available:

•

A rubber safety cap to cover the transceiver

•

A rubber safety cap to cover the fiber-optic cable connector

170

Dell PowerConnect J-Series J-EX8216 Ethernet Switch Hardware Guide

Содержание PowerConnect J-8216















































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды