Dell PowerConnect J-8216 Скачать руководство пользователя страница 115

Страница: 115 / 270

Figure 35: Pallet Fastener

Carefully slice open the tape that holds the top of the cardboard box closed and open
the top of the box.

Remove the cardboard accessory box from the center of the foam padding.

Remove the foam padding from the top of the box.

Slide the cardboard box off the pallet.

Remove the plastic cover from the switch chassis.

Use a 7/16-in. or 11-mm open-end or socket wrench to remove the four sets of bracket
bolts that secure the chassis to the shipping pallet.

10.

Unpack the accessory box and lay out the contents so that they are ready for use.

11.

Verify that your order includes all appropriate parts. See “Parts Inventory (Packing
List) for a J-EX8216 Switch” on page 101.

12.

Store the brackets and bolts inside the accessory box.

13.

Save the shipping box, pallet, and packing materials in case you need to move or ship
the switch at a later time.

Chapter 8: Installing the Switch

Содержание PowerConnect J-8216















































































































































































































































































Результаты поиска

Содержание PowerConnect J-8216

Отзывы:

Бренды по названию

Популярные бренды

Dell PowerConnect J-8216, Руководство по оборудованию

Результаты поиска

Содержание PowerConnect J-8216

Отзывы:

Бренды по названию

Популярные бренды