Dell P152G Скачать руководство пользователя страница 36

Страница: 36 / 102

Steps

1. Place the heat sink on the system board.
2. Tighten the seven (M2x3) captive screws that secure the heat sink to the system board.

NOTE:

Tighten the captive screws in the sequential order mentioned on the heat sink [7>6>5>4>3>2>1].

NOTE:

The number of screws varies depending on the configuration ordered.

Next steps

1. Install the

base cover

2. Install the

SD card

3. Follow the procedure in

After working inside your computer

I/O daughter board FFC

Removing the Input/Output daughter board FFC

Prerequisites

1. Follow the procedure in

Before working inside your computer

2. Remove the

SD card

3. Remove the

base cover

4. Remove the

fan

About this task

The following image indicates the location of the Input/Output daughter board FFC and provides a visual representation of the
removal procedure.

Removing and installing components

Содержание P152G







































































































Результаты поиска

Содержание P152G

Отзывы:

Похожие инструкции для P152G

Бренды по названию

Популярные бренды

Dell P152G, Руководство по обслуживанию

Результаты поиска

Содержание P152G

Отзывы:

Похожие инструкции для P152G

Бренды по названию

Популярные бренды