Dell P152G Скачать руководство пользователя страница 33

Страница: 33 / 102

The following images indicate the location of the heat sink and provide a visual representation of the removal procedure.

Steps

1. Loosen the four (M2x3) captive screws that secure the heat sink to the system board.

NOTE:

Loosen the captive screws in the reverse sequential order mentioned on the heat sink [4 > 3 > 2 > 1].

NOTE:

The number of screws varies depending on the configuration ordered.

2. Lift the heat sink from the system board.

Installing the UMA heat sink

Prerequisites

If you are replacing a component, remove the existing component before performing the installation process.

About this task

NOTE:

If either the system board or the heat sink is replaced, use the thermal grease provided in the kit to ensure that

thermal conductivity is achieved.

The following images indicate the location of the heat sink and provide a visual representation of the installation procedure.

Removing and installing components

Содержание P152G







































































































Результаты поиска

Содержание P152G

Отзывы:

Похожие инструкции для P152G

Бренды по названию

Популярные бренды

Dell P152G, Руководство по обслуживанию

Результаты поиска

Содержание P152G

Отзывы:

Похожие инструкции для P152G

Бренды по названию

Популярные бренды