Dell OptiPlex 5260 Скачать руководство пользователя страница 99

Страница: 99 / 111

Installing the display panel

Place the display assembly base in its upright position, and slide the display panel into the slot between the middle frame and the
display assembly base [1].

Route the touchscreen cable through the routing guide on the display assembly base.

Push the display backlight cable through the slots on the display assembly base [2].

Push the display panel towards the display assembly base, closing the gap between the display panel and the middle frame [3].

NOTE:

Ensure the display cable, touchscreen cable, and display backlight cable has been fully threaded through the slots on

the display assembly base before closing the gap between the display panel and the middle frame.

Removing and Installing components

Содержание OptiPlex 5260
















































































































Результаты поиска

Содержание OptiPlex 5260

Отзывы:

Похожие инструкции для OptiPlex 5260

Бренды по названию

Популярные бренды

Dell OptiPlex 5260, Руководство по обслуживанию

Результаты поиска

Содержание OptiPlex 5260

Отзывы:

Похожие инструкции для OptiPlex 5260

Бренды по названию

Популярные бренды