manualshive.com logo in svg

Dell Networking S6000 System, Справочное руководство

Поделиться
Скачать
Dell Networking S6000 System Скачать руководство пользователя страница 849

Version 9.2(0.2)

Introduced on the Z9000.

Version 9.0.2.0

Introduced on the S6000.

Version 
8.3.19.0

Introduced on the S4820T.

Version 
8.3.12.0

Introduced on the S4810.

Example

FTOSF>show isis int

GigabitEthernet 0/7 is up, line protocol is up

  MTU 1497, Encapsulation SAP

  Routing Protocol: IS-IS

    Circuit Type: Level-1-2

    Interface Index 37847070, Local circuit ID 1

    Level-1 Metric: 10, Priority: 64, Circuit ID: systest-3.01

     Hello Interval: 10, Hello Multiplier: 3, CSNP Interval: 10

    Number of active level-1 adjacencies: 1

    Level-2 Metric: 10, Priority: 64, Circuit ID: systest-3.01

     Hello Interval: 10, Hello Multiplier: 3, CSNP Interval: 10

    Number of active level-2 adjacencies: 1

    Next IS-IS LAN Level-1 Hello in 2 seconds

    Next IS-IS LAN Level-2 Hello in 1 seconds

    LSP Interval: 33

GigabitEthernet 0/8 is up, line protocol is up

  MTU 1497, Encapsulation SAP

  Routing Protocol: IS-IS

    Circuit Type: Level-1-2

    Interface Index 38371358, Local circuit ID 2

    Level-1 Metric: 10, Priority: 64, Circuit ID: systest-3.02

     Hello Interval: 10, Hello Multiplier: 3, CSNP Interval: 10

    Number of active level-1 adjacencies: 1

    Level-2 Metric: 10, Priority: 64, Circuit ID: systest-3.02

     Hello Interval: 10, Hello Multiplier: 3, CSNP Interval: 10

--More--

show isis neighbors

Display information about neighboring (adjacent) routers.

S6000

Syntax

show isis neighbors [level-1 | level-2] [detail] [

interface

]

Parameters

level-1

(OPTIONAL) Displays information about Level 1 IS-IS 
neighbors.

level-2

(OPTIONAL) Displays information about Level 2 IS-IS 
neighbors.

detail

(OPTIONAL) Displays detailed information about neighbors.

interface

(OPTIONAL) Enter the following keywords and slot/port or 
number information:

Intermediate System to Intermediate System (IS-IS)

849

Содержание Networking S6000 System







































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды