manualshive.com logo in svg

Dell Networking S6000 System, Справочное руководство

Поделиться
Скачать
Dell Networking S6000 System Скачать руководство пользователя страница 788

26

Intermediate System to Intermediate 

System (IS-IS)

The intermediate system to intermediate system (IS-IS) protocol for IPv4 and IPv6 is supported on the 
S6000platform.
IS-IS is an interior gateway protocol that uses a shortest-path-first algorithm. IS-IS facilitates the 
communication between open systems, supporting routers passing both IP and OSI traffic.

A router is considered an intermediate system. Networks are partitioned into manageable routing 
domains, called areas. Intermediate systems send, receive, and forward packets to other routers within 
their area (Level 1 and Level 1-2 devices). Only Level 1-2 and Level 2 devices communicate with other 
areas.

IS-IS protocol standards are listed in the Standard Compliance chapter in the 

Dell Networking OS 

Configuration Guide

.

NOTE: The fundamental mechanisms of IS-IS are the same between IPv4 and IPv6. Where there are 

differences between the two versions, they are identified and clarified in this chapter. Except where 

identified, the information in this chapter applies to both protocol versions.

adjacency-check

Verify that the “protocols supported” field of the IS-IS neighbor contains matching values to this router.

S6000

Syntax

adjacency-check

To disable adjacency check, use the 

no adjacency-check

 command.

Defaults

Enabled.

Command 
Modes

• ROUTER ISIS (

for IPv4

)

• CONFIGURATION-ROUTER-ISIS-ADDRESS-FAMILY-IPV6 (

for IPv6

)

Command 
History

This guide is platform-specific. For command information about other platforms, 
refer to the relevant 

Dell Networking OS Command Line Reference Guide

.

The following is a list of the Dell Networking OS version history for this command.

Version 9.0.2.0

Introduced on the S6000.

788

Intermediate System to Intermediate System (IS-IS)

Содержание Networking S6000 System







































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды