Dell Networking S6000 System Скачать руководство пользователя | Manualshive

Страница: 346 / 1510

background image

Version 7.8.1.0

Introduced on the S-Series.

Version 7.7.1.0

Introduced on the C-Series.

Usage
Information

Peering sessions are reset when you change the router ID of a BGP router.

This command automatically restarts the BGP instance for the configuration to
take effect.

clear ip bgp

Reset BGP sessions. The soft parameter (BGP Soft Reconfiguration) clears the policies without resetting

the TCP connection.

S6000

Syntax

clear ip bgp [vrf

vrf-name

] * |

as-number

|

ip-address

[flap-

statistics | soft [in | out]]

Parameters

vrf

vrf-name

Enter the keyword

vrf

and then the name of the VRF to

clear all BGP sessions corresponding to that VRF.

NOTE: Use this attribute to clear a BGP instance
corresponding to either a specific address family in a
default VRF or an IPv4 address family in a a non-default
VRF.

*

Enter an asterisk ( * ) to reset all BGP sessions.

as-number

Enter the AS number to reset all neighbors belonging to that
AS. The range is from 0 to 65535 (2 byte), from 1 to
4294967295 (4 byte), or from 0.1 to 65535.65535 (dotted
format).

ip-address

Enter an IP address in dotted decimal format to reset all
prefixes from that neighbor.

flap-statistics

(OPTIONAL) Enter the keyword

flap-statistics

to reset

the flap statistics on all prefixes from that neighbor.

soft

(OPTIONAL) Enter the keyword

soft

to configure and

activate policies without resetting the BGP TCP session, that
is, BGP Soft Reconfiguration.

NOTE: If you enter the

clear ip bgp ip-address

soft

command, both inbound and outbound policies

are reset.

in

(OPTIONAL) Enter the keyword

in

to activate only inbound

policies.

out

(OPTIONAL) Enter the keyword

out

to activate only

outbound policies.

346

Border Gateway Protocol

«
...
344
345
346
347
348
...
»

Содержание Networking S6000 System







































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для Networking S6000 System

Бренд: Black Box Страницы: 2

SRS Lighting DTS16F-DIN

Бренд: plasa Страницы: 4

Бренд: Tecsis Страницы: 2

Бренд: Ruby Tech Страницы: 301

Бренд: H-Tronic Страницы: 15

Бренд: WAGO Страницы: 36

EXT-HDMI-CAT5-844

Бренд: Gefen Страницы: 28

BOCAHUB-16 Plus BEN220

Бренд: Boca Страницы: 56

Бренд: CoolGear Страницы: 8

ENTERTAINMENT HUB

Бренд: Ev-ent Hire Страницы: 5

Бренд: Led Control Страницы: 22

ONW-D-1001-347-W

Бренд: Greengate Страницы: 2

Бренд: Huanyu Страницы: 10

Бренд: Targus Страницы: 30

GoControl WA00Z-1

Бренд: Nortek Страницы: 4

Бренд: Tecnoplastic Страницы: 16

SwitchView SC100

Бренд: Avocent Страницы: 2

Summit X430 Series

Бренд: Extreme Networks Страницы: 12

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды