manualshive.com logo in svg

Dell Networking S6000 System, Справочное руководство

Поделиться
Скачать
Dell Networking S6000 System Скачать руководство пользователя страница 342

Version 7.7.1.0

Introduced on the C-Series.

Usage 
Information

This feature is advertised to BGP neighbors through a capability advertisement. In 
Receiver Only mode, BGP saves the advertised routes of peers that support this 
capability when they restart.

BGP graceful restart is active only when the neighbor becomes established. 
Otherwise it is disabled. Graceful-restart applies to all neighbors with established 
adjacency.

This command automatically restarts the BGP instance for the configuration to 
take effect.

bgp non-deterministic-med

Compare MEDs of paths from different autonomous systems.

S6000

Syntax

bgp non-deterministic-med

To return to the default, use the 

no bgp non-deterministic-med

 command.

Defaults

Disabled (that is, paths/routes for the same destination but from different ASs do 
not have their MEDs compared).

Command 
Modes

ROUTER BGP

Command 
History

This guide is platform-specific. For command information about other platforms, 
refer to the relevant 

Dell Networking OS Command Line Reference Guide

.

The following is a list of the Dell Networking OS version history for this command.

Version 9.0.2.0

Introduced on the S6000.

Version 
8.3.19.0

Introduced on the S4820T.

Version 8.3.11.1

Introduced on the Z9000.

Version 8.3.7.0

Introduced on the S4810.

Version 7.8.1.0

Introduced on the S-Series.

Version 7.7.1.0

Introduced on the C-Series.

Usage 
Information

In Non-Deterministic mode, paths are compared in the order in which they arrive. 
This method can lead to Dell Networking OS choosing different best paths from a 
set of paths, depending on the order in which they are received from the neighbors 
because MED may or may not get compared between adjacent paths. In 
Deterministic mode (

no bgp non-deterministic-med

), Dell Networking OS 

342

Border Gateway Protocol

Содержание Networking S6000 System







































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды