manualshive.com logo in svg

Dell Networking S6000 System, Справочное руководство

Поделиться
Скачать
Dell Networking S6000 System Скачать руководство пользователя страница 322

9

Border Gateway Protocol

BGP is an external gateway protocol that transmits interdomain routing information within and between 

autonomous systems (AS). BGP version 4 (BGPv4) supports classless inter-domain routing (CIDR) and the 
aggregation of routes and AS paths. Basically, two routers (called neighbors or peers) exchange 

information including full routing tables and periodically sent messages to update those routing tables.
BGP is supported in Dell Networking OS version 9.0.2.0 for the S6000 platform

NOTE: For more information about configuring the border gateway protocol (BGP), refer to the BGP 
chapter in the 

Dell Networking OS Configuration Guide

.

This chapter contains the following sections:

• BGPv4 Commands
• MBGP Commands
• BGP Extended Communities (RFC 4360)
• IPv6 BGP Commands

BGP IPv4 Commands

Border Gateway Protocol (BGP) is an external gateway protocol that transmits interdomain routing 

information within and between Autonomous Systems (AS). BGP supports classless interdomain routing 

(CIDR) and the aggregation of routes and AS paths. Basically, two routers (called neighbors or peers) 

exchange information including full routing tables and periodically send messages to update those 

routing tables.

NOTE: Dell Networking OS supports 2-byte (16-bit) and 4-byte (32-bit) format for autonomous 

system numbers (ASNs), where the 2-byte format is 1 to 65535 and the 4-byte format is 1 to 

4294967295.

NOTE: Dell Networking OS supports dotted format as well as the traditional plain format for AS 

numbers. The dot format is displayed when using the 

show ip bgp

 commands. To determine the 

comparable dot format for an ASN from a traditional format, use ASN/65536. ASN%65536. For more 

information about using the 2– or 4-byte format, refer to the 

Dell Networking OS Configuration 

Guide

.

address-family

Enable the IPv4 multicast or the IPv6 address family.

S6000

Syntax

address-family [ipv4 {multicast | vrf 

vrf-name

} | ipv6 unicast]

Parameters

ipv4 multicast

Enter the keyword 

ipv4

 followed by the keyword 

multicast

 to enable BGPv4 multicast mode.

322

Border Gateway Protocol

Содержание Networking S6000 System







































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды