manualshive.com logo in svg

Dell Networking S6000 System, Справочное руководство, Страница: 155 / 1510

Поделиться
Скачать
Dell Networking S6000 System Скачать руководство пользователя страница 155

If the host fails authentication for the designated number of times, the 
authenticator places the port in authentication failed VLAN (

dot1x auth-fail-

vlan

).

NOTE: You can create the Layer 3 portion of a guest VLAN and authentication 
fail VLANs regardless if the VLAN is assigned to an interface or not. After an 
interface is assigned a guest VLAN (which has an IP address), routing through 
the guest VLAN is the same as any other traffic. However, the interface may 
join/leave a VLAN dynamically.

Related 
Commands

•

dot1x auth-fail-vlan

 — Configure an authentication failure VLAN.

•

dot1x reauthentication

 — Enable periodic re-authentication of the client.

•

dot1x reauth-max

 —

Configure the maximum number of times to re-authenticate a port before it 
becomes unauthorized

dot1x host-mode

Enable single-host or multi-host authentication.

S6000

Syntax

dot1x host-mode {single-host | multi-host | multi-auth}

Parameters

single-host

Enable single-host authentication.

multi-host

Enable multi-host authentication.

multi-auth

Enable multi-supplicant authentication.

Defaults

single-host

Command 
Modes

INTERFACE

Command 
History

This guide is platform-specific. For command information about other platforms, 
refer to the relevant 

Dell Networking OS Command Line Reference Guide

.

The following is a list of the Dell Networking OS version history for this command.

Version 9.0.2.0

Introduced on the S6000.

Version 9.0.0.0

Introduced on the Z9000.

Version 
8.3.19.0

Introduced on the S4820T.

Version 
8.3.12.0

Introduced on the S4810.

802.1X

155

Содержание Networking S6000 System







































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов