Dell Networking S6000 System Скачать руководство пользователя | Manualshive

Страница: 1456 / 1510

background image

Command
Modes

VLT DOMAIN PROXY GW STATIC

Command
History

Version 9.4(0.0)

Introduced on the S4810, S4820T, S6000, Z9000, and MXL
Switch.

Usage
Information

You can configure the remote MAC address of the VLT peer to be associated with
the static VLT proxy gateway and exclude a VLAN or a range of VLANs from proxy
routing. This parameter is for a static VLT proxy gateway configuration.

Example

Dell(conf)#vlt-domain 1

Dell(conf-vlt-domain#proxy-gateway static

Dell(conf-vlt-domain-proxy-gw-static)#remote-mac-address

00:01:e8:06:95:ac exclude-vlan 3

peer-domain-link port-channel exclude-vlan

Configure proxy-gateway LLDP, specify a port-channel and a VLAN or range of VLANs, and exclude a

VLAN or a range of VLANs from proxy routing.

S6000

Syntax

[no] peer-domain-link port-channel

interface-identifier

exclude-vlan

vlan-range

Parameters

port-channel

Configure the proxy-gateway interface port-channel. Port
channel range is from 1 to 128.

vlan-range

Enter the member VLANs using comma-separated VLAN IDs,
a range of VLAN IDs, a single VLAN ID, or a combination. For
example:

Comma-separated: 3, 4, 6

Range: 5-10

Combination: 3, 4, 5-10, 8

Command
Modes

VLT DOMAIN PROXY GW LLDP

Command
History

Version 9.4(0.0)

Introduced on the S4810, S4820T, S6000, Z9000, and MXL
Switch.

Usage
Information

You can configure the port channel interface that must be associated with the
LLDP proxy gateway and exclude a VLAN or a range of VLANs from proxy routing.
This parameter is for an LLDP proxy gateway configuration.

1456

VLT Proxy Gateway

«
...
1454
1455
1456
1457
1458
...
»

Содержание Networking S6000 System







































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для Networking S6000 System

Бренд: Yamamoto Electric Works Co., Ltd. Страницы: 15

Бренд: A-Neuvideo Страницы: 28

Бренд: Abseco Страницы: 10

Бренд: ADC Страницы: 75

SEHI SEHI100TX-

Бренд: Cabletron Systems Страницы: 75

Бренд: ATEN Страницы: 4

Бренд: Edge-Core Страницы: 65

Бренд: Black Box Страницы: 50

SECURVIEW SV-7020

Бренд: CrimeStopper Страницы: 1

Бренд: Eaton Страницы: 3

Бренд: Watt Stopper Страницы: 2

FASTHOME 550-030

Бренд: Steren Страницы: 4

Бренд: hager Страницы: 4

Бренд: GORMAN-RUPP PUMPS Страницы: 4

Бренд: Rosewill Страницы: 9

TIMEGUARD IS3N-20

Бренд: Theben Страницы: 2

Бренд: Imagine Страницы: 93

Бренд: TESmart Страницы: 34

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды