manualshive.com logo in svg

Dell Networking S6000 System, Справочное руководство

Поделиться
Скачать
Dell Networking S6000 System Скачать руководство пользователя страница 1267

port to which a client is connected. After authentication is successful, normal traffic passes through the 
port.
Dell Networking OS supports RADIUS and Active Directory environments using 802.1X Port 
Authentication.

Important Points to Remember

Dell Networking OS limits network access for certain users by using VLAN assignments. 802.1X with VLAN 
assignment has these characteristics when configured on the switch and the RADIUS server.

• 802.1X is supported on S6000.
• 802.1X is not supported on the LAG or the channel members of a LAG.
• If no VLAN is supplied by the RADIUS server or if 802.1X authorization is disabled, the port is 

configured in its access VLAN after successful authentication.

• If 802.1X authorization is enabled but the VLAN information from the RADIUS server is not valid, the 

port returns to the Unauthorized state and remains in the configured access VLAN. This prevents ports 

from appearing unexpectedly in an inappropriate VLAN due to a configuration error. Configuration 

errors create an entry in Syslog.

• If 802.1X authorization is enabled and all information from the RADIUS server is valid, the port is 

placed in the specified VLAN after authentication.

• If port security is enabled on an 802.1X port with VLAN assignment, the port is placed in the RADIUS 

server assigned VLAN.

• If 802.1X is disabled on the port, it is returned to the configured access VLAN.
• When the port is in the Force Authorized, Force Unauthorized, or Shutdown state, it is placed in the 

configured access VLAN.

• If an 802.1X port is authenticated and put in the RADIUS server assigned VLAN, any change to the port 

access VLAN configuration does not take effect.

• The 802.1X with VLAN assignment feature is not supported on trunk ports, dynamic ports, or with 

dynamic-access port assignment through a VLAN membership.

dot1x authentication (Configuration)

Enable dot1x globally; dot1x must be enabled both globally and at the interface level.

S6000

Syntax

dot1x authentication

To disable dot1x on globally, use the 

no dot1x authentication

 command.

Defaults

Disabled.

Command 
Modes

CONFIGURATION

Command 
History

This guide is platform-specific. For command information about other platforms, 
refer to the relevant 

Dell Networking OS Command Line Reference Guide

.

The following is a list of the Dell Networking OS version history for this command.

Version 
8.3.19.0

Introduced on the S4820T.

Security

1267

Содержание Networking S6000 System







































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды