Dell Latitude 5550 страница 8 Скачать руководство пользователя

Страница: 8 / 63

Removing and installing components

Recommended tools

The procedures in this document may require the following tools:

•

Phillips screwdriver #0

•

Phillips screwdriver #1

•

Torx #5 (T5) screwdriver

•

Plastic scribe—Recommended for field technicians.

Screw list

NOTE:

When removing screws from a component, it is recommended to note the screw type, the quantity of screws,

and then place them in a screw storage box. This is to ensure that the correct number of screws and correct screw type
is restored when the component is replaced.

NOTE:

Some computers have magnetic surfaces. Ensure that the screws are not left attached to such surface when

replacing a component.

NOTE:

Screw color may vary with the configuration ordered.

Table 1. Screw list

Component

Secured to

Screw type

Quantity

Screw image

Base cover

Palm-rest and
keyboard assembly

M2x3

Battery

Palm-rest and
keyboard assembly

M2x3

Battery

Palm-rest and
keyboard assembly

M2x4

Right fan

System board and
palm-rest and
keyboard assembly

M2x4

I/O board shield

I/O board

M2x4

Left fan

System board and
palm-rest and
keyboard assembly

M2x4

Solid-state drive1

System board

M2x2

solid-state drive2

System board

M2x2

Speakers

Palm-rest and
keyboard assembly

M2x2

Removing and installing components

Содержание Latitude 5550
































































Результаты поиска

Содержание Latitude 5550

Отзывы:

Похожие инструкции для Latitude 5550

Бренды по названию

Популярные бренды

Dell Latitude 5550, Руководство по обслуживанию

Результаты поиска

Содержание Latitude 5550

Отзывы:

Похожие инструкции для Latitude 5550

Бренды по названию

Популярные бренды