background image

Working inside your computer

Before working inside your computer

About this task

NOTE:

 The images in this document may differ from your computer depending on the configuration you ordered.

Steps

1. Save and close all open files and exit all open applications.

2. Shut down your computer. Click 

Start 

 Power

 > 

Shut down

.

NOTE:

 If you are using a different operating system, see the documentation of your operating system for shut-down

instructions.

3. Disconnect your computer and all attached devices from their electrical outlets.
4. Disconnect all attached network devices and peripherals, such as keyboard, mouse, and monitor from your computer.

CAUTION:

 To disconnect a network cable, first unplug the cable from your computer and then unplug the cable from

the network device.

5. Remove any media card and optical disc from your computer, if applicable.

Safety instructions

Use the following safety guidelines to protect your computer from potential damage and to ensure your personal safety. Unless otherwise
noted, each procedure included in this document assumes that you have read the safety information that shipped with your computer.

NOTE:

 Before working inside your computer, read the safety information that is shipped with your computer. For more

safety best practices, see the Regulatory Compliance home page at 

www.dell.com/regulatory_compliance

.

NOTE:

 Disconnect your computer from all power sources before opening the computer cover or panels. After you finish

working inside the computer, replace all covers, panels, and screws before connecting your computer to an electrical
outlet.

CAUTION:

 To avoid damaging the computer, ensure that the work surface is flat, dry and clean.

CAUTION:

 To avoid damaging the components and cards, handle them by their edges, and avoid touching the pins and

the contacts.

CAUTION:

 You should only perform troubleshooting and repairs as authorized or directed by the Dell technical

assistance team. Damage due to servicing that is not authorized by Dell is not covered by your warranty. See the safety
instructions that is shipped with the product or at 

www.dell.com/regulatory_compliance

.

CAUTION:

 Before touching anything inside your computer, ground yourself by touching an unpainted metal surface,

such as the metal at the back of the computer. While you work, periodically touch an unpainted metal surface to
dissipate static electricity which could harm internal components.

CAUTION:

 When you disconnect a cable, pull it by its connector or its pull tab, not the cable itself. Some cables have

connectors with locking tabs or thumb-screws that you must disengage before disconnecting the cable. When
disconnecting cables, keep them evenly-aligned to avoid bending the connector pins. When connecting cables, ensure
that the ports and the connectors are correctly oriented and aligned.

CAUTION:

 Press and eject any installed card from the media-card reader.

1

Working inside your computer

5

Содержание Latitude 5550
































































Отзывы: