Dell Latitude 5550 Скачать руководство пользователя

Страница: 14 / 63

NOTE:

Disconnecting the battery cable, removing the battery, or draining the flea power clears the CMOS and resets

the BIOS settings on your computer.

NOTE:

After your computer is reassembled and powered on, it prompts for the Real Time Clock (RTC) reset. When

the RTC reset cycle occurs, the computer restarts several times and then an error message is displayed– "Time of
day not set". Enter the BIOS when this error appears and set the date and time on your computer to resume normal
functionality.

4. Disconnect the battery cable from the system board.
5. Turn your computer over and press the power button for 15 seconds to drain the flea power.

Installing the base cover

Prerequisites

If you are replacing a component, remove the existing component before performing the installation procedure.

About this task

The following images indicate the location of the base cover and provide a visual representation of the installation procedure.

Removing and installing components

Содержание Latitude 5550
































































Результаты поиска

Содержание Latitude 5550

Отзывы:

Похожие инструкции для Latitude 5550

Бренды по названию

Популярные бренды

Dell Latitude 5550, Руководство по обслуживанию

Результаты поиска

Содержание Latitude 5550

Отзывы:

Похожие инструкции для Latitude 5550

Бренды по названию

Популярные бренды