Dell Latitude 5401 Скачать руководство пользователя страница 78 | Manualshive

Страница: 78 / 122

Dell Latitude 5401 Скачать руководство пользователя страница 78

Steps

1. Locate the display cable and display hinges on your computer.
2. Remove the transparent sticker covering the display cable to the system board.
3. Peel the tape that secures the display cable to the system board.
4. Open the latch, and disconnect the display cable from the system board.
5. Remove the two screws (M2.5x4) and (M2x3) that secure the left-display hinge to the system board.
6. Remove the two screws (M2.5x4) that secure the right-display hinge to the system board.
7. Open the display hinges at an angle of 90 degrees.
8. Gently slide the palm-rest and keyboard assembly off the display assembly carefully.

Installing the display assembly - discrete

Prerequisites

If you are replacing a component, remove the existing component before performing the installation procedure.

About this task

The figure indicates the location of the component and provides a visual representation of the installation procedure.

78

Lahtivõtmine ja kokkupanek

«
...
76
77
78
79
80
...
»

Содержание Latitude 5401



























































































































Отзывы:

Нет отзывов