manualshive.com logo in svg

Dell Latitude 5401, Руководство по обслуживанию, Страница: 35 / 122

Поделиться
Скачать
Dell Latitude 5401 Скачать руководство пользователя страница 35

About this task

NOTE:

 Slot 1 supports both M.2 2230 and M.2 2280 SSD.

The figure indicates the location of the solid-state drive in slot 1 and provides a visual representation of the alignment procedure to
accommodate the M.2 2280 solid-state drive.

Steps

1. Align the solid-state drive bracket to accommodate the M.2 2280 solid-state drive.
2. Replace the single (M2x3) screw to secure the solid-state drive module to the palm-rest and keyboard assembly.

Next steps

1. Connect the 

battery

.

2. Install the 

base cover

.

3. Follow the procedure in 

after working inside your computer

.

Removing the M.2 2230 solid-state drive - SSD-1 -
discrete

Prerequisites

1. Follow the procedure in 

before working inside your computer

.

2. Remove the 

base cover

.

3. Disconnect the 

battery

.

About this task

NOTE:

 Slot 1 supports both M.2 2230 and M.2 2280 SSD.

The figure indicates the location of the M.2 2230 solid-state drive in slot 1 and provides a visual representation of the removal procedure.

Lahtivõtmine ja kokkupanek

35

Содержание Latitude 5401



























































































































Отзывы:

Нет отзывов