Dell Inspiron 8500 Скачать руководство пользователя страница 51

Страница: 51 / 75

Palm Rest: Dell Inspiron 8500/8600 Service Manual

Back to Contents Page

Palm Rest

Dell™ Inspiron™ 8500/8600 Service Manual

CAUTION:

Before performing the following procedures, read the safety instructions

in your

Owner's Manual

NOTICE:

To avoid electrostatic discharge, ground yourself by using a wrist grounding strap or

by periodically touching an unpainted metal surface (such as the back panel) on the computer.

1. Follow the instructions in "

Preparing to Work Inside the Computer

2. Remove the

keyboard

NOTICE:

You must remove the display assembly before you remove the palm rest; the display

hinges pass through the back of the palm rest.

3. Remove the

display assembly

4. Remove the

microprocessor thermal-cooling assembly

5. Remove the

video card

6. Remove the 13 M2.5 x 12-mm screws from the bottom of the computer.

file:///I|/SERVICE%20MANUALS/DELL%20MANUALS/...TH%20PARALLEL%20SERIAL_SERV_MAN/palmrest.htm (1 of 4)6/21/2004 1:12:27 AM

Содержание Inspiron 8500












































































Результаты поиска

Содержание Inspiron 8500

Отзывы:

Dell Inspiron 8500, Руководство по обслуживанию, Страница: 51 / 75

Результаты поиска

Содержание Inspiron 8500

Отзывы: